Dimensions of Curt Trailer Hitch Receiver C15800 for Ram Cab and Chassis

Question

Question:

Hi Just wondered if you may know the dimensions of the Curt #C15800 hitch please Regards

asked by: Rob

0

Expert Reply:

I have attached for you below a detailed dimensional drawing of the Curt Trailer Hitch Receiver part # C15800 which is a confirmed fit for the vehicles listed below. The trailer hitch has a class V rating with 2-1/2" opening which is great for heavy duty towing.

2010 - 2022 Ram 3500 Cab and Chassis
2010 - 2022 Ram 4500 Cab and Chassis
2010 - 2022 Ram 5500 Cab and Chassis

expert reply by: Conner L

0

Dimensions of Curt Trailer Hitch Receiver C15800 for Ram Cab and Chassis
(click to enlarge)

Answer 1

34 inch wide frames are pretty common for cab and chassis vehicles. For a hitch that fits that dimension we have the #C15800 which sits down 7 inches from where it attaches to the truck frame. This would be the best option we have.

view full answer...

Answer 2

I just went out to the warehouse and measured the Curt Trailer Hitch Receiver item #C15845. I have attached a couple of diagrams with the dimensions of this hitch on them. From the center of the back bolt to the front of the receiver is 26" The…

view full answer...

Answer 3

Flat towing setups end up pretty involved so I wouldn't say there's a super easy route to go but there are some areas that can be made a little easier. For a base plate kit you would want the Blue Ox part #BX1716 if you do not have adaptive…

view full answer...

Answer 4

The Curt Trailer Hitch Receiver part #C15400 and the Curt Trailer Hitch Receiver part #C15800 are the exact same trailer hitch save for one has a 2" receiver tube opening and the other a 2-1/2" receiver tube opening. The dimensional drawing…

view full answer...

Answer 5

I do have an option for you but they don't offer custom fit hitches for motorhome chassis. The best option is a universal fit hitch which are typically only available in class III weight rating ranges. For this, I recommend the Multi-Fit…

view full answer...

Answer 6

I had our warehouse measure the Curt Trailer Hitch Receiver #C15703 you were looking at, and has an overall width of 40-5/8", overall length of 29". The distance between the vertical mounting holes is 14-1/2" center to center, and the…

view full answer...

Answer 7

The Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2" #C15802 has 3 different hole dimensions for mounting. The two holes closest to the receiver are 36.31 inches on center. The widest holes are 37 inches on center and…

view full answer...

Answer 8

The width of your frame indicates that your 2012 Ford F-450 is most likely a cab and chassis model which has the frame width a few inches than a standard truck bed. But if you can measure the distance between the mounting holes on the frame of your…

view full answer...

Answer 9

Hello John. The part number 801171 is the Lippert Unity X1 Control Board. I just spoke with my contact at Lippert who said that these are not available aftermarket, but if you already have the 801171 unit on board then you can get a replacement. You…

view full answer...

Answer 10

Curt 2-1/2-inch Class V hitch #C15845 will fit the 1999 Ford F-450 cab and chassis so long as the frame width (measured outside to outside) is 34-inches. Drilling is required for installation. I went to our warehouse and measured the side-to-side…

view full answer...

Answer 11

Given that your vehicle is not listed on our fitguide for available hitches, one option with your provided dimensions is the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver #41990-07. With this hitch, you will be able to adjust the 9-1/2…

view full answer...

Answer 12

If the Freightliner chassis is a Sprinter then none of the hitches available, see link, are rated for 10,000 pounds. They max out at 7,500 when using weight distribution. You will also want to consult the vehicle owners manual for the towing capacity…

view full answer...

Dimensions of Curt Trailer Hitch Receiver C15800 for Ram Cab and Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching