/
Optronics/
Tail Lights/
Strip Light/
LED Light/
RedItem # STL264RCB
Our Price: $18.54
Orders above $99 qualify for Free Shipping
20-1/2" x 1". 4-Function, waterproof light bar acts as brake, tail, turn, and backup light. Red lens set inside clear lens. Mounts to trailer surface - hardware not included. 4-Wire pigtail. DOT compliant. 19 Diodes.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
California residents: click here
Video of Fusion LED Combination Tail Light Bar for Trailers over 80" Wide - Submersible - Clear Lens
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the Fusion LED Combination Tail Light Bar for Trailers Over 80" Wide. This is going to be a submersible light with a clear lens. This is going to have a multi-function light. We're going to have our red LEDs to act as our stop, turn, and tail light. At the bottom, we'll have four white LEDs to act as our reverse light.It has a clear lens all the way down, so show our lights clearly. I'm going to connect this to ground.
My white wire's going to be my ground wire, and then my black wire will be the running light circuit. So go ahead and turn that on. As you can see, we'll have our running lights there. If we tap our yellow wire, that's going to be that reverse signal. Our red wire will be the brake or the turn signal.Go ahead and turn the lights out in the studio, so you can get a better idea what that's going to look like in the dark.
So again, running light signal going to be a little bit dimmer. Then our reverse light, need it pretty bright to illuminate behind us, so we can see what's going on behind our trailer. Then our brake and turn signal.So as you can see, it's going to be a nice bright light with all our functions that we're going to need. Again, those functions are going to be white for ground, black for tail light or running light circuit, red for our stop and turn signal, and then yellow for our reverse signal.Now the nice thing about this is that it is going to be sonically sealed. Basically that just means that this is going to be a waterproof light.
So it's going to work really well for any applications where you're going to be getting in and out of the water and need to submerge this light, maybe on a boat trailer or something like that. It's also just going to mean that it's going to be impervious to any water getting in there, so it's going to be a really long-lasting light.At the back, you'll see where all our wires come through. Those are actually covered with a sort of potting material, kind of like a silicone that's sitting in there to just seal all that up. So we don't have to worry, again, about anything getting in and causing any corrosion or shorts with our wire.Now this also is going to have a surface-mount design, so it's going to attach via the two holes at either end. This does not come with any hardware to get it attached, so you will have to find some separately.Another thing about our LEDs is that these are going to be a great improvement over any incandescent bulbs since we don't have to worry about changing any bulbs since these are going to last for a long time.
They're going to last up to 50 times longer than your incandescents.This also has a durable surface-mount technology, which just basically means that it's going to be attached to a surface that's going to be better able to withstand shock, so you won't have to worry about bumpy roads causing your lights to short out. It's going to also have a better heat distribution, so our lights are just going to be that much longer lasting. The housing and lens are going to be made of a durable polycarbonate.This is going to be DOT compliant. It meets all SAE compliant ratings for our trailers over 80 inches wide. As far as our dimensions with this light, it is going to be 20.5 inches long from end to end. Then it's going to be about an inch wide and about three-quarters of an inch deep. The distance between our mounting holes is going to be 19 and five-eighth inches.In total, we'll have 19 diodes. Our power draw at 12.8 volts is going to be .265 amps for our stop and turn signal. Our tail lights are going to have .24 amp draw. Our backup light will have .3 amps.Optronics also has a lifetime warranty on the LEDs.That's going to do it for our look at the Fusion LED Combination Tail Light Bar for Trailers over 80" Wide with a submersible design and a clear lens.
Average Customer Rating: 4.9 out of 5 stars (15 Customer Reviews)
20-1/2" x 1". 4-Function, waterproof light bar acts as brake, tail, turn, and backup light. Red lens set inside clear lens. Mounts to trailer surface - hardware not included. 4-Wire pigtail. DOT compliant. 19 Diodes.exactly as stated 605422
Review from a similar Optronics Fusion LED in Trailer Lights
The shipping was prompt. I added these lights on the motorcycle rack that I installed on the back of our 5th wheel. The motorcycle tires kind of blocked the trailer lights. The lights look great. The brake / turn and back up lights are nice and bright. The tail lights could be a little brighter but I can add a strip light in the center if I choose. 652542
Review from a similar Optronics Fusion LED in Trailer Lights
Great light. Would have like to see a rubber gasket around this for a better seal. But all in all a good light. 385584
Review from a similar Optronics Fusion LED in Trailer Lights
A clean and simple light that's easy to lnstall at a great price 475297
well one out of 6 as failed now Im not sure if there worth the money
craig l - 02/13/2019
Review from a similar Optronics Fusion LED in Trailer Lights
What a great product. I have had these for a year and they work great! 562308
Review from a similar Optronics Fusion LED in Trailer Lights
Please see attached photos of my lights installed on a trailer. These lights are a direct replacement for the stock optronics stop/turn/tail lights on my Sundowner horse trailer. It was pre wired from the factory for backup lights but none were installed. If you pull off the rear right side light cover of the trailer there is a yellow wire that is capped off. Double Check with a light tester that it is the power wire for reverse lights. I drilled out the old rivets and installed the new lights with the reverse light wired up to the yellow power wire The leds are nice and bright for all functions 486302
Review from a similar Optronics Fusion LED in Trailer Lights
Good replacement for an existing light on our travel trailer. Trailer was wired for backup lights but none installed. This unit will give me tail, turn, brake and backup lights. Measurements for mounting holes was exact. Did not have to drill other holes. This is a surface mount. I did have to modify the reflective trim ring that was on my original light for it to fit the new light. The housing on this light was slightly larger but the overall dimensions were the same. Some grinding on the trim with the drimmel tool solved the problem. Would be good for initial installation also. Initial installation would require a hole near the center of mount location to allow wiring to pass through trailer. Seems to be a quality product. Attached photos of lights installed. 392556
Lights are still functioning as they are supposed to. Have had no issues with them.
Dar B - 06/13/2018Review from a similar Optronics Fusion LED in Trailer Lights
These lights are fantastic and a direct replacement on my EZ Loader boat trailer. Just had to drill the screw holes and attach wires. Done deal. The LED lights are good and bright, and the back up lights serve their purpose perfectly. 668967
Review from a similar Optronics Fusion LED in Trailer Lights
Nice lamps . Real bright. 663138
Review from a similar Optronics Fusion LED in Trailer Lights
I just got a new boat and had damaged the trailer light no other place around had a matched light even the large outdoor shop (starts with a C) sold me the incorrect ones for $60. Then as frustration started impacting me. I saw etrailers online, saw a light that was identical, took a chance and it was the exact light for only 1/3 of the price I paid at the large outdoor store. End result, I'm very pleased with my purchase, shipping and overall. 658879
Review from a similar Optronics Fusion LED in Trailer Lights
Installed on boat trailer a year ago. Super bright and works great. 639583
Review from a similar Optronics Fusion LED in Trailer Lights
Good 603682
Review from a similar Optronics Fusion LED in Trailer Lights
Used these on my 1985 custom pickup truck flatbed conversion, they look good and are very bright. Only complaint is that the wires come out of the unit in a "straight line " so you either have to "mill" a slot in the mounting panel or drill a large hole. 554361
Review from a similar Optronics Fusion LED in Trailer Lights
Great light, really bright, and fast de livery 539147
Review from a similar Optronics Fusion LED in Trailer Lights
Fair prices, fast shipping, and handle returns well. Good company to deal with. 387546
Ask the Experts about this Optronics Trailer Lights
Do you have a question about this Trailer Light?
Do you have a question about this Trailer Light?
At etrailer.com we guarantee:
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.