To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
California residents: click here
The hitch was easy to install--just bolt it on. It was a bit of a wrestle to get it past the tailpipe but with a little prying, it slipped into place. All of the necessary bolts came with the kit.
Fit-up on our 2002 Sienna was excellent and painless. This is one of the easiest hitch installations I've ever done. The recommended 3-3/4" drop ball mount put us about 11" off the ground, which was way too low. We switched to a 2" drop mount, and that leveled our trailer almost perfectly (we were aiming for 14", and hit about 13-1/2").
etrailer sent my order right away. The trailer hitch was very easy to install although I did elect to lower the muffler to make the installation easier. It is great for towing my lawnmower trailer and boat trailer. I also found the same hitch at a lower price at another retailer and etrailer lived up to their low price guarantee and refunded the price difference. What a great company !
Purchased a curt hitch and plug and play harness adaptor for an 03 sienna. Timely delivery, correct products, installed easily. Would order again from this vendor.
This was easy to put in place. Follow the instructions and it will be just fine.
The mechanic that installed the hitch said it fit perfect.
I bought this hitch for my 2002 Toyota Sienna. I love that it requires no additional drilling or welding, since I don't usually drill straight. It is perfectly designed for my van, is discreet, and is rated at the full towing capacity of the vehicle.
I plan to tow a 4x8 utility trailer occasionally for camping, biking, or other utility purposes until my budget allows for a 7-passenger SUV.
The instructional video was excellent for installation. I installed this hitch in the driveway with a handful of common tools. The installation took an hour, much of which was lowering and re-attaching the muffler hanger.
NOTE: When you remove the rubber hanger, remove from the muffler rather than from the steel hanger welded into the car. I expect that some future time when my rubber hanger needs replaced, the muffler shop will have to remove the hitch for sufficient clearance to access the hanger. It's pretty close-fitting.
NOTE: the bolts that ship with this hitch have a 17-MM head. Different from the 14-MM head that came with my van's tow-hooks. Check your sockets to see that you have the right size.
I got help just for 5 minutes, when I needed an assistant to help hold the hitch up to the holes while I set the bolts in.
It is solid and strong, lined up perfectly, and is completely tucked up under the bumper except for the 2" receiver.
I am completely satisfied with my purchase.
Perfect Design!
This hitch fit my 2000 Toyota Sienna perfectly. I even did not have to remove the muffler and the spare tire. I just removed the old 1-1/4 hitch receiver then installed the new 2" hitch which I ordered from e-trailer. No drill required, all holes on the new hitch were aligned perfectly to the holes of t
Perfect Design!
I ordered this hitch from e-trailer for my 2000 Toyota Sienna. It came sooner than expected. It was a one person job. I did not have to remove the spare tire and the muffler to install the new hitch receiver, but if no body help you, you will need two jacks. One is to raise up and hold the other end of the new hitch to align the holes. The other end you can hold by hand or use the second jack to hold it for you because it was heavy. Then tighten the bolts. No drilling required.
S. H.
4/14/2017
It works fine. no problems at all.
Perfect fit and quality! Just what I ne eded!
Joseph
11/3/2018
The hitch is still rock solid after a year! I’m expecting it to outlast the vehicle.
Fit and finish are excellent. Installed on a 1999 Toyota Sienna without issue. No Complaints.
Perfect fit. Installation instructions were clear. Held up well to a Michigan winter, no rust. But on top of all that, the customer service at etrailer.com is absolutely fantastic. I called late in the day and the rep was able to get the part on that day's shipment even though there were only minutes until the delivery truck pulled away.
John P.
8/9/2020
Still working great one year in. No signs of rust or wear - even with the salted roads in Michigan. Cant say that for the rest of the vehicle
2000 Toyota Sienna. It went on easy. No need to drop the exhaust. I have a Curt 5 bicycle carrier that goes right in it. I have hit the ground once in two months of having it on the van and that was my fault for hurrying through a huge dip that had an uphill drive on the other side. The only problem I had with the install was the washers that were included did not fit on the new bolts. I had some that fit just nice laying around at home.
Phillip
4/20/2017
Still working good. We use it for a bike rack for 5 bikes.
Ease of ordering. Hitch came in a timely manner. Installation was as easy as other reviewers have stated! Might require two people, one to hold in place, the other to install...but other than that-great!
Brandi
4/13/2022
Great! Rust free and holding strong! Thank you!
Welds and workmanship on the hitch assembly is as good as it gets.
Only took about 20 minutes to install. The most difficult part of the install is lowering the muffler. The easiest way to do that is shoot some WD-40 or similar lubricant onto the rubber isolator/ hangers and slide them off their body support dowels with a long screwdriver or pry tool.
Note: Make sure both rubber hangers are installed on the body support dowels before bolting hitch in position.
The trailer wiring harness adapter conversion to 4 pin flat worked great, and had plenty of wire to make a professional appearing routing easy.
I installed a new CURT hitch on my 1998 Toyota Sienna mini-van yesterday. I like the hitch very much for the Sienna and relatively light-duty apps. I'll use the rig to pull a 3500-pound boat and trailer about a half mile from storage to water and to carry a cargo platform on 650-mile trips.
The hitch simply bolts on without drilling after removal of two factory-installed tow-eyes at each rear corner. If intended for heavier apps, I would use one of the hitch models that requires drilling because those designs are more heavy-duty.
Another feature that I like is that the front-end of the CURT receivers are open. I can't removed the hitch bar from the receiver on my 1995 pickup due to heavy corrosion between the hitch bar and receiver. The front of the receiver is closed so there's no way to get a penetrant into that space without drilling news holes.
Another nice feature for me is that only the receiver is visible from behind the vehicle. The heavy tube that spans between the frame is out-of-sight and hidden behind the bumper.
The install was easy with only two minor items of note.
1) Removing the rubber muffler hanger was the most difficult chore. After lubing the rubber-metal contact and trying to pry the two apart, I placed the flattened end of my cheater pipe against the rubber hanger and struck the other end of the pipe with a 2-lb hammer to separate the hanger from the bracket. I also had to use the cheater and hammer to re-assemble.
2) Intending to re-use, I cleaned and lubed the original fasteners that I removed before I realized that new, longer fasteners were enclosed in the receiver cavity.
etrailer's Curt hitch for my 1998 Toyota Sienna installed easily, looks great. I enlisted a service station owner with a lift to help me. We were able to install the unit without dropping the exhaust in less than a half hour. Looking forward to getting a similar hitch for my 2012 Sienna.
Haven't installed yet but I like working with trainer
Easy install. I got the trailer light wiring kit too. I would buy again. It pulls a 5x10 utility trailer for firewood quite well.. Sherry was excellent.
Very easy to install since everything fit perfectly.
Well made and easy to install on my 2000 Toyota Sienna minivan for a bike rack. I highly recommend etrailer and will consider them again when I need a hitch for my next vehicle.
This trailer was super easy to install on my Toyota Sienna. (It took me less than 30 minutes.) It works great and I load it up with the family bike rack all the time.
Great price and a great product.
I could not be happier with this trailer hitch, both the product quality and the amazing instructional video. The hitch went on without any problems and in around 30 minutes. I also purchased the trailer wire harness which is really well made and also went in very fast. They even give you zip ties for a tidy install. I HIGHLY recommend this hitch, the wiring harness and etrailer for excellent customer service!
Trailer Hitch Reciever C13511 fits just fine. Took a bit of manuvering to get it by the tail pipe but it went on without removing anything, including the spare tire. A small hammer moved it into exact position. As advertized it took about 30 minutes save the final tightening of the mounting bolts. It took almost as long to get all the staples out of the shipping box.
The Curt trailer hitch receiver that I received from etrailer was delivered promptly and was easy to install. At first I thought that I would have to lower my tailpipe, but I was able to maneuver it in place without lowering the tail pipe.
I am very pleased with the information provided by etrailer.
Great receiver and a breeze to install! Watched the product video and installed it on my 2002 Toyota Sienna in about 10 minutes. Use it to tow a jon boat and a utility trailer. Highly recommend. Also the shipping was extremely fast! Thanks!
Do you have a question about this Trailer Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Merinda
2/11/2015
I have owned this hitch for a year, now. It is still sturdy and strong. I havent noticed much rust - and that right around my rusty receiver. Its a solid, strong chunk of steel.The 2002 Sienna was one of the best minivans for towing right off the assembly line, with a good engine and decent suspension for a van. We have towed a 14-foot 1000-lb trailer occasionally and pretty close to home 100 miles.More frequently we have towed a little 4x8 flat trailer. That went on a 1000-mile camping trip and lots of local runs for plywood and moving the odd bits of furniture or lawn mowers or whatever.I am thinking of getting a cargo tray. Id be a bit concerned about scraping bottom in some driveways and subdivision dips, though. I would choose a design that will get the tray above the receiver without hang-downs, also trying to avoid interfering with the hatch. I havent done it yet, though, so I cant say which would be best. That isnt a concern of the hitch so much as the van, though.I am completely satisfied with my purchase. I have recommended the same to a couple friends with the same era of Sienna.