See what our Experts say about this Rhino Rack Roof Rack

• Does Rhino-Rack HD Roof Rack for 2020 Toyota Corolla Sedan Have Static Load Rating
  I checked with Rhino-Rack and they specifically mention they only have dynamic (moving) load ratings, and that is exactly what the 165 lb capacity is with the rack that fits your 2020 Toyota Corolla sedan. Rooftop tents generally only call for a rack to have a certain dynamic capacity so I recommend checking out your tent's manual to find out. As for the roof rack for your 2020 Toyota Corolla, here are the parts you need: - Rhino-Rack Heavy-Duty Roof Rack Crossbars # # RB1250B-2 (Black)...
  view full answer...
  
• Dimensions of Rhino-Rack Heavy-Duty Roof Rack Crossbars
  The Rhino-Rack Heavy-Duty 50-Inch Roof Rack Crossbar # RB1250S has cross-section dimensions of 1-7/8-inches tall and 1-5/8-inches wide, as shown in the photo I prepared for you. We also offer two bars as a set # RB1250. The vehicle known as the Mitsubishi Pajero in other countries is called the Montero in the North American market. If you happen to have a 2006 model year with factory installed roof rails that run front-to-back this crossbar can be installed using leg kit part # CXB.
  view full answer...
  
• Can I Carry Two Kayaks Side by Side on My Roof Rack?
  The roof rack you're asking about is a Rhino-Rack System with parts # RB1250, # RRRLKHD, # DK376 which has 50" long crossbars. As for if you can carry two kayaks lying down side by side, it's unlikely, but depends on your kayaks. Kayak widths can range from 22" to 30". If you have saddle-style kayak carriers like the Malone SaddleUp Pro # MPG110MD and your kayaks are less than 24" in width, then you can set them up side by side. If your kayaks are too wide though, you can get two J-style...
  view full answer...
• Crossbar Pads to Carry a Surf Board on Rhino-Rack Heavy Duty Crossbars
  Yes, we do have foam pads that will fit around your Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1250 and allow you to carry your surf board. You can use the Rhino-Rack Crossbar Pads w/ Tie-Downs # RRRWP04. These pads will fit your HD crossbars. I have included a picture from the instructions manual that shows this as a fit.
  view full answer...
  
• 2017 Hyundai Tucson Heavy Duty Roof Rack Recommendation
  Thank you for all of the info! I definitely have a roof rack solution so you can carry some ladders with your 2017 Hyundai Tucson but at this time (February 2022) Rhino-Rack doesn't have a roof rack fitment for your Tucson so we won't be able to install a roof rack using the Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1250. As an alternative option I recommend going with the Yakima HD Crossbar roof rack system. The crossbars won't increase the weight capacity of the roof rack since your...
  view full answer...
• Is Rhino-Rack 2500-Series Roof Rack Compatible with Thule Force Cargo Box # TH624
  The Rhino-Rack 2500-Series roof racks can include either square Euro crossbars, their Vortex Aero bars or their heavy-duty rectangular bars. The Euro square bars and the Vortex Aero bars both are fully compatible with the Thule Force XT Cargo Box # TH6356B. The heavy-duty cross bars # RB1250 are not. The Thule Force XT requires that the spread between the crossbars be at least 23-5/8-inches. As long as the rack has this minimum spread and uses one of the two compatible bar types it will...
  view full answer...
• Can I Use The Batwing Awning # RR33200 With My Factory Crossbars?
  The Rhino Rack Batwing Awning # RR33200 is a bolt on installation so it won't be able to work with your factory crossbars. You'll need to add another roof rack system with tracks to be able to use the batwing awning. You can use something like these legs # CXB and these bars # RB1250. These have a channel which will work with the hardware on the Batwing. You will need this mounting kit # RR31102. I personally have not used the XTM 270 Batwing Awning before. So I think that the batwing...
  view full answer...
• How to Determine if Rhino-Rack CXB Leg Kit Fits a 2022 Subaru Forester for HD Bars & Roof Top Tent
  The Rhino-Rack CXB Leg Kit for Raised, Factory Roof Rack Side Rails # CXB will fit the factory rails on your 2022 Subaru Forester as long as those rails are not more than 1-1/2" tall and not more than 2-1/4" wide. This would allow you to use Rhino Rack HD cross bars like the Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1250. It is also important to note that since these use the Rhino Rack HD bars, you may have a difficult time finding a rooftop tent that fits. That is because the HD bars...
  view full answer...
• Weight Capacity Of The Rhino Rack RLTF Roof Rack System.
  If you used these # RLTF feet with the tracks # RRRTV188 and use the Heavy Duty Crossbars # RB1250 you will have 220 lbs of capacity on your roof. This is a bit more than the average roof rack system so you will be able to really fill up your bar space! You should verify that the vehicle's roof can handl that weight too though.
  view full answer...
• What are the Dimensions of the Hi-Lift Jack Mounting Brackets # RJHB
  I went out to the warehouse and found that the internal dimension of the Hi-Lift Jack Mounting Brackets # RJHB would allow a post that is about 1" thick and about 2-3/4" high. These come with T-bolts that let you mount them on Rhino-Rack Heavy-Duty roof-rack crossbars like part # RB1250.
  view full answer...
  
• Sturdy Roof Rack Recommendation for 2008 Chevy Cobalt
  For a vehicle like your 2008 Chevy Cobalt I would not want to recommend a track style of rack as the best option. The tracks aren't going to flex enough to fit well and the clamp style racks are much sturdier than one might think so even though that's not the option you listed wanting it would be your overall best option still. Rhino Rack does offer a heavy duty roof rack that fits your vehicle with the # RB1250, # RRRLKHD, and # DK181 if you have a sedan or part # DK182 for a coupe but...
  view full answer...
• Heavy Duty Roof Rack Recommendation for 2013 Hyundai Sonata
  For stuff like lumber from a home center type store I would recommend the Rhino Rack HD roof rack part numbers # RB1250, # RRRLKHD, and # DK250 as it is confirmed as a fit and has large square bars that are great for what you are looking for. For load stops you would then want the pat # RRRLH1. Then for cinch straps part # RRRTD35P. This rack has a capacity of 110 lbs but you would also need to check the roof capacity of your vehicle in the owners manual.
  view full answer...
• Will the Inno Shadow 16 Fit on Rhino-Rack Crossbars on My 2013 Toyota Prius?
  As far as the fitment of the Inno Shadow 16 Cargo Box # INBRA1210BK being able to clamp around a Rhino-Rack roof rack, it depends on what type of Rhino-Rack crossbars you have on your 2013 Toyota Prius. If you have an aero crossbar system that involves the Rhino-Rack Vortex crossbars like the ROC25 # RR44SR, the Shadow 16 will clamp around those as well. The only caution is that the Shadow 16 will not fit Rhino-Rack Heavy Duty Crossbars like the # RB1250. I am happy to say that all 4...
  view full answer...
  
• Will the 65" Rhino-Rack HD Crossbars # RB1650 Fit on My 2010 Mazda 3 Hatchback?
  I have an answer for you. Unfortunately, the 65 inch Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1650 are too long for your 2010 Mazda 3 Hatchback with fixed mounting points. With that being said, you can still have shorter Rhino-Rack Heavy-Duty crossbars on your vehicle. Our installation team here at etrailer has tested these shorter bars with your vehicle so that they will fall within the required dimensions of local traffic laws. For this system, you will need the following parts:...
  view full answer...
• Will the Rhino-Rack RTC-Style Roof Rack Tracks # RTC95JW Fit a 1998 Jeep Wrangler with Hardtop
  The 37-1/2" long Rhino-Rack RTC-Style Roof Rack Tracks # RTC95JW are a universal fit so as long as your 1998 Jeep Wrangler Sahara has a naked roof that is flat then they will fit. The tracks provide mounting points for the Rhino-Rack # RLTP, # RLTF, and # RLT500 track-mounted legs. These are compatible with the Heavy-Duty Rhino-Rack Bars like the 50" long # RB1250.
  view full answer...
• Will the Rhino-Rack HD Crossbars Allow Me to Transport 2 Kayaks on My 2014 Kia Sorrento LX?
  Yes, the Rhino-Rack Heavy-Duty Roof Rack Crossbars - Black - 50" Long - Qty 2 # RB1250B-2 (black) and # RB1250 (silver) are compatible with the bare roof on your 2014 Kia Sorrento LX without a vista roof. For a complete roof rack system, you will need the following parts: - Rhino-Rack 2500 Series Legs for Heavy-Duty Crossbars - Naked Roofs or Fixed Mounting Points - Qty 4 # RRRLKHD - Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs - Naked Roof # DK179 For a J-style carrier...
  view full answer...
• How Do Roof Racks Attach to a 2012 Hyundai Elantra
  Rhino-Rack 2500 Series Leg Kit # RRRLKHD is just the legs but for them to actually fit your 2012 Hyundai Elantra you need the proper clamp kit. If you have a 4-door sedan with no rails or crossbars already on the roof you would use clamp kit # DK301 and bars # RB1250. If you have a Touring model with no rails or crossbars you would use clamp kit # DK010 and bars # RB1250. Clamp kits have what is basically a hook that attaches to the roof right above the doors in the door jamb. If you...
  view full answer...
• Leg Spacers for the Rhino-Rack RCH Legs
  If you're looking for the leg spacers to mount Heavy-Duty crossbars to your RCH Legs, part # RRRCH6, then the correct part number for those are # RRQMHD05. With these, you'll be able to mount Rhino-Rack HD Bars, part # RB1250. This may seem confusing at first because the fit-guide states that these are not compatible with your 2007 Lexus GX 470. However, in this particular (and very rare) case, the specific vehicle does not matter because these are attaching to the legs. In other words,...
  view full answer...
• Roof Rack Recommendation to Carry 2 Kayaks on 2014 Toyota Prius C and 2010 Toyota Prius
  There is a Rhino Rack roof rack that will fit both vehicles if you switch out the Custom DK Clamps and Pads. For the 2010 Toyota Prius, you will want the following parts: Crossbars # RB1250 Leg Kit # RRRLKHD Custom DK Clamps and Pads # DK195 For your 2014 Toyota Prius C you will want to add Custom DK Clamps and Pads # DK351. Before you attempt to carry 2 kayaks on the roof of your Prius you will need to consult your owner's manual to determine if you have the carrying capacity for...
  view full answer...
• Recommendations for Rhino-Rack HD Roof Rack on a 2013 Volkswagen Jetta Sedan
  I am happy to help you find a roof rack for your 2013 Volkswagen Jetta Sedan. For naked roofs, the roof rack will mount to the door frame of your vehicle using a custom fit hook. The Rhino-Rack HD # RB1650 does not have a confirmed fit custom mount for your Jetta, but the # RB1250 does. You will need the legs # RRRLKHD and custom fit kit # DK055 to complete your roof rack system. Check out the video below for a detailed explanation on how these racks are installed and why the custom...
  view full answer...
• Rhino-Rack Heavy Duty Roof Rack for 2018 Volkswagen Passat
  The Rhino-Rack # Y01-140B-NT is designed to fit roof mounted tracks such as what would be found on a camper shell, it's not typically used on a vehicle roof. You can install a similar rack using the following parts: • Rhino-Rack Heavy Duty 50 inch crossbars, part # RB1250B-2 for black or # RB1250 for silver • Series 2500 Legs, part # RRRLKHD • Vehicle-Specific fit clips, part # DK323 This rack has a 165 lb capacity and is custom designed to fit your vehicle.
  view full answer...
• Parts Needed to Move Rhino-Rack 2500 Series Roof Rack to 2014 Toyota Prius C
  A vehicle-specific portion of the Rhino-Rack roof racks for your 2014 Toyota Prius C is the Custom DK Clamps and Pad kit # DK351 that you referenced and this kit is used for a number of their 2500-series racks. You may also need a leg kit; which one will depend on the crossbars you have (the 2500 series includes several types). If you have the heavy-duty crossbar # RB1250 you will use leg kit # RRRLKHD; if you have Aero crossbars you'll instead use # RRRLKVA. The link provided will show...
  view full answer...
• Availability of Rhino-Rack Heavy Duty Roof Rack Option for 1997 Nissan Pathfinder w/ Roof Tracks
  We do indeed have a system that would work on your Pathfinder. In order to use the Rhino Rack Heavy Duty 50 inch long crossbars on your 1997 Pathfinder, you would use the leg system Rhino Rack specifically designed for the recessed roof tracks, part # RLTFMV. The rack has a 220 lb capacity, which could be limited by the roof's actual capacity if it's lower than that of the rack.
  view full answer...
• Weight Capacity and Bike Rack Options For 2018 Nissan Rogue
  In that question, the customer may have been referring to the towing capacity of their vehicle being a maximum tongue weight of 110lbs. That information can be found in your owners manual. So even if Draw-Tite Max-Frame Trailer Hitch Receiver # 75902 has a 3,500 pound towing capacity and 350 pound tongue weight capacity, the towing capacity of the vehicle takes precedent. So the lowest of the two numbers is what you go with in regards to towing capacity. So please check the towing capacity...
  view full answer...
• Will the Heavy Duty Rhino-Rack Roof Rack Fit a 2015 Nissan NV 3500?
  I have a great alternative for your crossbar setup. Unfortunately, the Rhino-Rack Roof Rack for Thule and Yakima Tracks # Y01-140B-NT is not confirmed to fit your 2015 Nissan NV 3500. However, we do carry a similar heavy duty bar setup by Rhino-Rack that does fit your 2015 Nissan NV 3500. For this setup, I recommend the following parts: - Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1375B-2 - Rhino-Rack 2500 Series Legs for Heavy-Duty Crossbars # RRRLKHD - Custom DK Fit Kit for 4 Rhino-Rack...
  view full answer...
  
• Do Parts of Rhino Rack Roof Rack From 2012 Ford Escape Fit 2014 Ford F-150 SuperCrew Cab?
  I checked with Rhino Rack and the square bar roof racks that fit a 2012 Ford Escape and 2014 Ford F-150 do share the same # RRRLKHD 2500 Series legs which are for HD crossbars, so if that's what you have you would be able to use those legs on your F-150. If you have different legs there is NOT going to be a fit. Apart from that you are correct that you would need new crossbars and a new fit kit. The correct crossbars for the '14 F-150 would be the Rhino-Rack Heavy-Duty Roof Rack Crossbars...
  view full answer...
• Are Feet and Fit Kit Available for Rhino Rack HD Rack RR28DP for Silverado
  Hey Jonathon, we do have just the replacement feet of the # RR28DP available with the part # RRRLKHD and the fit kit # DK427. I'd definitely brag to your wife how much money you saved just getting the feet and reusing your current bars haha.
  view full answer...
• Rhino-Rack Heavy-Duty or Vortex Crossbars for 2019 Ford Transit Connect
  The primary difference between the Rhino-Rack Heavy-Duty Crossbars and the Rhino-Rack Vortex Aero Crossbars has to do with what they are designed to carry and what accessories work well with them. The Heavy-Duty Crossbars feature built-in C-channels that are made specifically for Rhino-Rack Heavy-Duty accessories like the Hi-Lift Jack Mounting Brackets # RJHB. Because the bars are larger than most other systems they will not be compatible with a lot of accessories that aren't specifically...
  view full answer...
  
• Recommended No-Drill Roof Rack System To Attach A Rhino Rack Pioneer Platform On 2017 Ram 1500
  To attach the Rhino-Rack Pioneer Platform Roof Tray - Aluminum - 60" Long x 56" Wide # RR42113BF to your 2017 Ram 1500 Crew Cab without drilling you'll need to first install the Rhino-Rack Heavy-Duty Roof Rack Crossbars - Black - 59" Long - Qty 2 # RB1500B-2, Rhino-Rack 2500 Series Legs for Heavy-Duty Crossbars - Naked Roofs or Fixed Mounting Points - Qty 4 # RRRLKHD, and the Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs - Naked Roof # DK043. This system will clamp onto...
  view full answer...
• Does Rhino-Rack HD Roof Rack for 2020 Toyota Corolla Sedan Have Static Load Rating
  I checked with Rhino-Rack and they specifically mention they only have dynamic (moving) load ratings, and that is exactly what the 165 lb capacity is with the rack that fits your 2020 Toyota Corolla sedan. Rooftop tents generally only call for a rack to have a certain dynamic capacity so I recommend checking out your tent's manual to find out. As for the roof rack for your 2020 Toyota Corolla, here are the parts you need: - Rhino-Rack Heavy-Duty Roof Rack Crossbars # # RB1250B-2 (Black)...
  view full answer...
  
• Which Heavy Duty Crossbar Setup Should I Use On My 2015 Ford F-350 Super Duty?
  I am showing that the correct Rhino-Rack heavy duty crossbar setup for your 2015 Ford F-350 crew cab is Rhino-Rack Heavy-Duty Roof Rack Crossbars - Black - 59" Long # RB1500B-2. You will also need Leg Kit # RRRLKHD and Fit Kit # DK190 to install this onto your roof. This has a 165lb weigh capacity and is 59" long. You can install accessories by clamping onto the crossbars or by using the T-slot track. I have attached an installation video showing this roof rack being installed on a different...
  view full answer...
• Can I Carry Two Kayaks Side by Side on My Roof Rack?
  The roof rack you're asking about is a Rhino-Rack System with parts # RB1250, # RRRLKHD, # DK376 which has 50" long crossbars. As for if you can carry two kayaks lying down side by side, it's unlikely, but depends on your kayaks. Kayak widths can range from 22" to 30". If you have saddle-style kayak carriers like the Malone SaddleUp Pro # MPG110MD and your kayaks are less than 24" in width, then you can set them up side by side. If your kayaks are too wide though, you can get two J-style...
  view full answer...
• Will the Rhino-Rack Heavy-Duty Roof Rack Fit 2015 Ram 1500 Crew Cab with Sunroof
  Yes, the Rhino-Rack Heavy-Duty Roof Rack, which consists of parts # RB1500, # RRRLKHD, and # DK043, will fit your 2015 Ram 1500 crew cab with a sunroof. Placement of the crossbars is very specific and I have included an attachment which illustrates the measurements for your Ram, as well as the measurement process. With these measurements you will be able to determine exactly where the crossbars will sit in comparison to your sunroof.
  view full answer...
  
• Recommended Heavy Duty Roof Rack for 2016 Ford F-150
  I may have a solution for you, however I don't recommend trimming the Rhino-Rack RT-Style Roof Rack Tracks like the 58 Inch # RRRTV148 that you referenced. These strips do feature pre-cut holes for the rivets so trimming any portion of the units will essentially change the way they are meant to attach. You would also need to make sure that the cuts are perfectly straight up and down so the end caps will fit properly. We do have shorter lengths available, such as the 36-1/4 inch # RRRTS540,...
  view full answer...
• Dual Kayak Carrier For 2017 Ram 1500 With Tonneau Cover
  I would recommend getting the Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1500, the Rhino-Rack 2500 Series Legs for Heavy-Duty Crossbars # RRRLKHD and the Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs # DK043. I've included a video to help you install if you wanted to go that route. Then the most cost effective carrier would be four of the Malone Rack Pads # MPG314, two per crossbar. The foam pads will be less rough on your kayaks whenever you're going down gravel roads....
  view full answer...
• How Was Rhino Rack Roof Rack Spread for 2014 Chevy Silverado 1500 Decided
  Roof rack companies like Rhino Rack pick the required spread for their roof racks like the # RB1500, # RRRLKHD, and # DK377 based on where the roof is reinforced the best. We have to recommend you always go with the required spread, otherwise you could potentially damage the roof of your vehicle or the rack may not secure properly. Even though the spread is narrower than you'd like (most racks are right at this same spread) you can still use a canoe carrier like the Yakim KeelOver # Y04069...
  view full answer...
• Roof Rack and Platform Recommendation for Roof of 2013 Toyota Highlander
  I have a solution for you, you'd want the Rhino Rack HD roof rack part # RB1375B-2, # RRRLKHD, and # DK138 which will allow you to use a Pioneer Platform Tray part # RR42112BF with the adapter part # RR43105. This has a lower capacity listed for what you are wanting to do but that's based on the application of it being used on the highway. For a situation like yours where the weight won't be bouncing around this would work well assuming your Highlander also has a similar weight capacity....
  view full answer...
• Ladder Rack Recommendation for Camper Shell on 2002 Toyota Tacoma
  We have just what you need. For a rack system that will attach to the camper shell you have installed on your 2002 Toyota Tacoma the TraRac CapRac part # TH29200XT is a confirmed fit and would work well. This is a fixed rack that attaches directly to the cap. See picture. I also attached an install video link for you to check out as well.
  view full answer...
  
• Carrying Plywood Sheets on a 2011 Subaru Forester
  I have a solution for you, but we do not carry large enough roof baskets for this application. Instead, I'd choose a rack that is at least a little wider than the lumber you're intending to carry. This will give you ample room to support the sheet itself, and give you additional room for the tiedowns you'll need in order to keep the panels secure. I've included a link to the range of 54 inch and wider bar kits that fit a 2011 Subaru Forester, but I have a recommendation based on compatibility...
  view full answer...
• Tonneau Cover and Rack Options for 2007 Honda Ridgeline
  The tonneau cover manufacturers do offer some covers for other trucks that have the T-slots in the side rails that can be used tor installing a ladder rack like the Yakima OverHaul HD, but unfortunately they don't offer anything like this for your 2007 Honda Ridgeline. If the 165 lb capacity of a standard roof rack would work for you, your best bet would be to go with a tonneau cover like the BAK BAKFlip F1 you'd looked at, part # BAK72601 and use a roof rack on the vehicle. I'd recommend...
  view full answer...
• Roof Rack and Canoe Carrier Recommendation for a 2008 Chevy Silverado
  A Rhino Rack Roof Rack that includes the part # RRRLKHD would do an excellent job for carrying a 15 foot canoe on your 2008 Chevy Silverado. The rest of the parts needed to complete the roof rack would be the part # RB1375B-2 and # DK227. This is one of the strongest racks we offer so it would definitely take a lot of abuse. It would be great for carrying your canoe. For securing a canoe upside down on the crossbars I would recommend the Ratchet Grab part # RRRRG. I spoke to my contact...
  view full answer...
• How to Mount Putco 40 LED Light Bar on 2006 Honda Ridgeline
  The Putco Luminix Off-Road LED Light Bar # P10040 is a fit for your 2006 Honda Ridgeline as long as you have the Bumper Mounting Bracket # P2255 installed, yes. In order to install something without modifying anything on your Ridgeline we'll have to install a roof rack, like the Rhino-Rack HD model listed below, and then use same-brand LED light mounting brackets like what we find with part # RR43174. 59" HD Crossbars - # RB1500B-2 2500 Series Legs - # RRRLKHD Fit Kit - # DK155 Since...
  view full answer...
• Roof Rack and 2-Kayak Carrier for 2016 Honda Accord Sport Sedan
  The Rhino-Rack ROC25 Series Heavy-Duty roof rack for your 2016 Honda Accord Sport Sedan that is made of parts # RB1375, # RRRLKHD and # DK359 is indeed a confirmed fit for your car. But note that this rack's unusual bar profile means reduced compatibility of accessory items like kayak carriers. You will have fewer kayak carrier choices with this rack. Instead I suggest their Vortex Aero rack # RR32SR which features quieter aerodynamic crossbars that will generate much less wind noise than...
  view full answer...
• Weight Capacity and Comparison of Rhino Roof Racks for a 2011 Acura RDX
  I spoke with my contact for Rhino Rack and he said the weight capacity for all Rhino-Rack roof racks for your 2011 Acura RDX is 110 lbs. I think you were looking at the Rhino-Rack Heavy-Duty roof rack with the Heavy-Duty crossbars, # RB1375, the leg kit, # RRRLKHD, and Custom DK Clamps and Pads, # DK177. The Heavy-Duty crossbars will have a higher weight capacity, but once they are installed on a 2011 Acura RDX, the entire roof rack capacity drops to 110 lbs due to the limitations on the...
  view full answer...
• Sturdy Roof Rack Recommendation for 2008 Chevy Cobalt
  For a vehicle like your 2008 Chevy Cobalt I would not want to recommend a track style of rack as the best option. The tracks aren't going to flex enough to fit well and the clamp style racks are much sturdier than one might think so even though that's not the option you listed wanting it would be your overall best option still. Rhino Rack does offer a heavy duty roof rack that fits your vehicle with the # RB1250, # RRRLKHD, and # DK181 if you have a sedan or part # DK182 for a coupe but...
  view full answer...
• Do I Have To Drill Afer Installing The Tracks On The Rhino Rack Roof Rack System # Y01-120-NT?
  The foot # RRRLKHD to crossbar # RB1375B-2 is adjustable along the bar with the kit you're looking at # Y01-120B-NT. The only drilling required is to install the tracks so if they are already installed no need to do any more drilling.
  view full answer...
  
• Kayak Carrier Recommendation for 2009 Ford F-150 With Factory Folding Tonneau Cover
  A ladder rack is one option for transporting your kayak on your F-150 that has the dealer-installed folding tonneau cover, but note there can sometimes be interference between the common mounting requirements for tonneau covers and ladder racks since both install on the bed rails. I can offer you a simple and very cost-effective option IF your tonneau cover can handle the weight of your kayak. We offer foam block carriers that are very inexpensive, simple to install and that weigh very...
  view full answer...
• How Can I Tell if I have Fixed Mounting Points on My 2015 Mazda CX-5 for a Crossbar System?
  According to the specs I have, you may have fixed mounting points on those rubber strips on your 2015 Mazda CX-5. The way you can tell is if there is a small removable tab on those rails that cover the holes. I went ahead and attached a video of a 2015 Mazda CX-5 with fixed mounting points to give you perspective about what to look for. If you determine that you have fixed mounting points, I recommend the following setup: - Rhino-Rack Vortex Aero Crossbars - Aluminum - Black - 46" #...
  view full answer...
• Roof Rack and Kayak Carrier for 2018 Mitsubishi Outlander Sport
  I will be happy to walk you through what you will need to add a roof rack and kayak carrier to 2018 Mitsubishi Outlander Sport in the budget you mentioned. You said there are places to install a rack system, but I am unsure if that meant your '18 Outlander Sport had a naked roof (meaning no rails of any kind on the roof already) or a roof with factory flush-mounted rails that run front to back so I'll give you options for both. Rhino Rack is a high-quality roof rack manufacturer and they...
  view full answer...
  
• Recommended Roof Cargo Box for 42 Inch Crossbar Spread on 2010 Mazda CX-9
  Based on my research, it does look like you are correct that the minimum crossbar spread on your 2010 Mazda CX-9 using the fixed mounting points will be around 42 inches. We only have a few cargo boxes available that are compatible with this large of a spread. The most economical box we have that will work with up to a 42 inch crossbar spread is the Yakima SkyBox 12 # Y07334. This cargo box provides 12 cubic feet of space and a dual-side-opening lid that allows you to load/unload cargo...
  view full answer...
• Roof Rack and Paddle Board Carrier Recommendation for 2015 Mitsubishi Outlander Sport
  Thank you for the information! For an all-in-one system we have the SeaSucker Surfboard Carrier # 298-BX1806. This uses powerful vacuum cups (rated for 210 lbs pull strength per cup) to secure to your roof and it comes with pads and tie-downs to easily secure your paddle board. The nice thing about this system is you can take it off and store it in the back of your 2015 Mitsubishi Outlander Sport when you aren't using it. If you'd rather have a more traditional roof rack that remains...
  view full answer...
  
• Roof Rack Recommendation for 2013 Hyundai Elantra GT
  The roof rack I recommend for your 2013 Hyundai Elantra GT without a sunroof is the Rhino Rack roof rack part # RRVA118B-2, # RRRLKVA, and # DK289 because this rack is easy to install, comes with locks, has aero shaped bars which means it will be quieter and because the rack is one of the highest quality racks available but not quite as expensive as the other brands of similar quality. This would work great with the Thule Canyon XT cargo basket part # TH859XT that you referenced as well.
  view full answer...
• Roof Rack for 2016 Mazda CX-5 with Naked Roof
  Thule recently redesigned their complete roof rack lineup so the older parts you mentioned right now will not be able to be used on your 2016 Mazda CX-5 but we do have great options that would work great like the Rhino Rack Vortex roof rack part numbers # RRVA118B-2, # RRRLKVA, and # DK289 which gives you the higher quality like Thule but at a better price. For a kayak carrier the # TH849000 would be a great choice as well as it's padded and can fold down when not in use.
  view full answer...
• Recommended Roof Rack And Cargo Solution For A 2015 Mazda Cx-5 With A Naked Roof
  We definitely have a couple options to store stuff outside the vehicle and a roof rack and basket will be a great option. I do have another potential way to go that I will lay out at the end, but I will start with the roof option. I also like the price point of Rhino Rack parts, so I tend to recommend them. With that being said, for your 2015 Mazda CX-5, you will need to start with the DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs # DK289. These will attach to fixed mounting points...
  view full answer...
• What Size Screw is Required for 2012 Mazda CX-9 Roof Rack?
  If you are looking for the screw size for the factory mount locations, you will use M6 screws that are 35 mm long which come in the Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs - Fixed Mounting Points # DK289. For a roof rack, I recommend this fit kit along with the Rhino-Rack Vortex Aero Crossbars # RRVA126B-2 and the 2500 Series Legs # RRRLKVA. Since you asked from a Yakima bar, the Yakima fit kit uses M6x28mm, M6x33mm and M6x40mm hardware as well as M8x35mm. These...
  view full answer...
• Roof Rack for a 2016 Hyundai Elantra GT
  Your kit is exactly what you noted, the Rhino Rack Aero Roof Rack, consisting of: Rhino Rack 46 Aero Style Bar, part # RRVA118B-2 Leg Kit, part # RRRLKVA Custom DK Fit Kit for 2500 Series, part # DK289 This kit will not work if your vehicle is a 2016 Hyundai Elantra GT with the panoramic surnoof.
  view full answer...
• Roof Rack for 2008 Mazda 3
  Rola used to have roof rack kits for your 2008 Mazda 3 that would mount to those fixed points but those parts were phased out by Rola. If you want a roof rack, you will need the Rhino Rack system with parts # RRVA118B-2, # RRRLKVA, # DK289. This mounts to the fixed mounting points on your 2008 Mazda 3. Rhino-Rack makes great roof racks that are a bit more budget-friendly compared to Thule and Yakima. Their construction is also really solid and have a weight capacity of 165 lbs. I attached...
  view full answer...
• Recommendation for Carrying 10 Foot Kayak on Roof of 2012 Hyundai Accent 5-Door
  There certainly are a vast number of ways to carry your kayak on your vehicle! I am happy to help sort through the options for you. The first step to carry your kayak on the roof of your 2012 Hyundai Accent will be to add a roof rack. A great option is the Rhino Rack Aero Bar Roof Rack with Vortex Aero Crossbars # RRVA118B-2, 2500 Series Legs # RRRLKVA, and the Custom Fit Kit # DK289. These crossbars are designed with an aerodynamic shape and vortex strips to help cut down on wind drag...
  view full answer...
• Roof Rack to Fit in Fixed Rain Gutter Mounting Points on a 2015 Mazda CX-5
  The Thule roof racks that will fit your 2015 Mazda CX-5 with a naked roof will all have a clamp-on system that holds the feet to the roof with a metal clip that attaches to the top of the door jamb. Side rails are not needed for this style. But I take it that you do not want that style either. For a roof rack that will fit into the fixed points that are in the rain gutter channels you can use a Rhino-Rack roof rack using bars # RRVA118B-2, leg kit # RRRLKVA, and fit kit # DK289.
  view full answer...
• What Bike Racks Are Compatible With The Rhino-Rack 2500 Roof Rack Square Crossbars
  All three of those bike racks are compatible. The Rhino-Rack 2500 Roof Rack - Square Crossbars - Naked Roofs or Fixed Mounting Points - 46" Long, part # DS118B, is a roof rack with square crossbars. Nothing is ever absolute, but almost all of our roof bike racks will be compatible with this rack. Finding the one that is the best fit will depend on the features that are most important to you. All of the bike racks in your question are wheel mounted bike racks. For me, the most important...
  view full answer...
• Roof Rack To fit 2016 Hyundai Accent Hatchback for Installing Roof Cargo Basket
  If you are wanting to install a roof cargo basket like the Yakima LoadWarrior part # Y07070 on a 2016 Hyundai Accent you will need to have a roof rack installed that has crossbars that run from left to right. The most popular option for a roof rack that fits the hatchback model of a 2016 Accent is the Rhino Rack part # RRVA118B-2, # RRRLKVA, and # DK289. With this installed the Yakima basket would fit and work well.
  view full answer...
• How Can I Transport My Roof Nest Tent on My 2015 Mazda CX-5 with a Bare Roof?
  Due to your 2015 Mazda CX-5 having a naked roof, you'll need to look into an alternative method below for installing your tent as there is not a heavy-duty rack compatible with your vehicle that'll carry your 185lb roof nest tent. If you are determined to have a tent setup on your vehicle, the absolute best way is to use a small utility trailer with crossbars such as the Malone EcoLight Sport Trailer - 58" Crossbars - 400 lbs # MAL53FR. This trailer comes with 400 pounds of static weight...
  view full answer...
• Transporting Mountain Bikes and Kayaks with the 2018 Mazda CX-5
  Hello, that you already have a trailer hitch installed is great. I suggest the use of a hitch mounted bike rack for your mountain bikes. For the kayak, you will need to transport that on the roof, we will begin with selecting roof rack options and then an appropriate carrier. For the crossbars I prefer the aero style as they have less wind resistance when not hauling items therefore less road noise relative to other styles such as the square tubing or round. I suggest the Rhino-Rack...
  view full answer...
• Vortex Crossbar Strip Measurements for Rhino-Rack Roof Rack on 2013 Mazda 3 Hatchback
  It sounds like you are trying to find out the needed strip length for both sides of the Rhino-Rack Vortex Crossbars # RRVA118B-2 on your 2013 Mazda 3 Hatchback, which are used in conjunction with the 2500 Series Legs # RRRLKVA and the Custom DK Fit Kit # DK289. I reached out to my contact at Rhino Rack and she said for your Mazda 3 Hatchback the front crossbar strip length should be 18.1 centimeters and the rear crossbar strip should be 16.8 centimeters. She said that the instructions...
  view full answer...
• Will the 65" Rhino-Rack HD Crossbars # RB1650 Fit on My 2010 Mazda 3 Hatchback?
  I have an answer for you. Unfortunately, the 65 inch Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1650 are too long for your 2010 Mazda 3 Hatchback with fixed mounting points. With that being said, you can still have shorter Rhino-Rack Heavy-Duty crossbars on your vehicle. Our installation team here at etrailer has tested these shorter bars with your vehicle so that they will fall within the required dimensions of local traffic laws. For this system, you will need the following parts:...
  view full answer...
• Can Sunroof Be Open And Will Rhino-Rack 2500 Roof Rack Interfere With Antenna On 2016 Mazda CX5
  The Rhino-Rack roof rack you asked about will work great on the roof of your CX-5. We always recommend keeping the sunroof closed due to the possibility of interfering with anything mounted on the crossbar and the excessive noise from the crossbars when traveling. I have attached a photo of the roof rack on the roof and the position of the antennae. As you can see the roof rack is mounted forward of the antennae so there will be no issue with the roof rack. To order this roof rack...
  view full answer...
  
• Bike Rack Options For A 3 Bike Carrier On A 2014 Mitsubishi Outlander Sport
  Although we do not currently carry a trunk mount back rack option that allows you to carry multiple bikes on your 2014 Mitsubishi Outlander Sport, I do have another solution that will allow you to carry three bikes. The only trunk mount bike rack option we currently have as a fit for your vehicle is our SeaSucker Hornet Rear Window Bike Rack part # 298-BH1302 which only carries one bike. This leaves you with two options. Option A involves the installation of one of our trailer hitches...
  view full answer...
• 2013 Mitsubishi Lancer Roof Rack Recommendation for Fixed Mounting Points
  Sounds like you have the 2013 Mitsubishi Lancer 5-Door Sportback and for that I recommend checking out the Rhino-Rack Vortex roof rack which consists of the following: 49" Vortex Crossbars - # RRVA126B-2 2500 Series Legs - # RRRLKVA DK Fit Kit - # DK289 This is designed for the fixed mounting points on your vehicle so you'll get a nice, clean looking setup. If you let me know what you plan on using this roof rack for I'd be more than happy to make another recommendation for you. Attached...
  view full answer...
• Recommended Roof Racks for Mitsubishi RVR 2018
  We have roof racks that are a confirmed fit for your 2018 Mitsubishi RVR. If you have a naked roof you'd want the Rhino Rack kit part numbers # RRVA126B-2, # RRRLKVA and # DK289 which is a confirmed fit and would work well. If you have flush rails on your roof that you can't put your hand under you'd instead want the Rhino Rack roof rack part # RRVA126B-2 and # RRSX031. I also attached a link to a page that has all of the roof rack options we have for your vehicle as well.
  view full answer...
• Compatibility of Rhino-Rack Vortex Aero Roof Rack Legs with 2014 Mazda CX-5 with OEM Fixed-Points
  Rhino-Rack's 2500 Series Leg kit # RRRLKVA is a confirmed fit on the 2014 Mazda CX-5 with OEM fixed-point mounts as well as on the sedan and hatchback versions of the 2013 Impreza. To use these on the CX-5 you will also need the fit kit # DK289. You can then install your Vortex Aero bars, such as the 44-inch black bars # RRVA118B-2.
  view full answer...
• Recommendation for a Roof Rack for a 2017 Mitsubishi Outlander Sport
  On the 2017 Mitsubishi Outlander Sport, you have two possible type roof styles: flush mount rails that run front to back or no existing rails or a naked roof. I have a recommendation for each style roof. For the roof with flush rails, I recommend the Rhino-Rack Vortex Roof Rack, # RRVA126B-2 Vortex Aero Crossbars, and # RRSX031 SRB Legs. The Vortex Aero Bars are constructed out of sturdy and lightweight aluminum and have a sleek low profile design. The aerodynamic design of these Rhino-Rack...
  view full answer...

Do you have a question about this Roof Rack?