Will the 65" Rhino-Rack HD Crossbars # RB1650 Fit on My 2010 Mazda 3 Hatchback?

Question

Question:

I have a Mazda 3 2010 hatchback with fixed mounting points. Will this item fit? [It seems close to a mazda 3 sport?] Can I order this item?

asked by: Jeffrey E

0

Expert Reply:

I have an answer for you. Unfortunately, the 65 inch Rhino-Rack Heavy-Duty Roof Rack Crossbars # RB1650 are too long for your 2010 Mazda 3 Hatchback with fixed mounting points. With that being said, you can still have shorter Rhino-Rack Heavy-Duty crossbars on your vehicle. Our installation team here at etrailer has tested these shorter bars with your vehicle so that they will fall within the required dimensions of local traffic laws. For this system, you will need the following parts:

- Rhino-Rack Heavy-Duty Roof Rack Crossbars - Silver - 50" Long - Qty 2 # RB1250
- Rhino-Rack 2500 Series Legs for Heavy-Duty Crossbars - Naked Roofs or Fixed Mounting Points - Qty 4 # RRRLKHD
- Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs - Fixed Mounting Points # DK289

With this above roof rack, you will be able to transport accessories and cargo on your 2010 Mazda 3. The weight capacity of this system is 165. In order to make sure that you don't extend over the maximum weight capacity of the roof of your Mazda 3, I recommend consulting the owner's manual for the maximum weight capacity of the roof of your vehicle.

expert reply by: Bob C

0

Answer 1

The Rhino-Rack ROC25 Vortex #RR93GR is an aerodynamic, low profile rack. I verified with Rhino-Rack that the bars are just as strong as the Rhino-Rack heavy-duty racks, however since the bars fit directly into the feet and do not have any over hang…

view full answer...

Answer 2

I am showing that the correct Rhino-Rack heavy duty crossbar setup for your 2015 Ford F-350 crew cab is Rhino-Rack Heavy-Duty Roof Rack Crossbars - Black - 59" Long #RB1500B-2. You will also need Leg Kit #RRRLKHD and Fit Kit #DK190 to install…

view full answer...

Answer 3

The Rhino-Rack Heavy-Duty 50-Inch Roof Rack Crossbar #RB1250S has cross-section dimensions of 1-7/8-inches tall and 1-5/8-inches wide, as shown in the photo I prepared for you. We also offer two bars as a set #RB1250. The vehicle known as the…

view full answer...

Answer 4

I have a solution for you, you'd want the Rhino Rack HD roof rack part #RB1375B-2, #RRRLKHD, and #DK138 which will allow you to use a Pioneer Platform Tray part #RR42112BF with the adapter part #RR43105. This has a lower capacity listed for what…

view full answer...

Answer 5

Thank you for all of the info! I definitely have a roof rack solution so you can carry some ladders with your 2017 Hyundai Tucson but at this time (February 2022) Rhino-Rack doesn't have a roof rack fitment for your Tucson so we won't be able…

view full answer...

Answer 6

If you used these #RLTF feet with the tracks #RRRTV188 and use the Heavy Duty Crossbars #RB1250 you will have 220 lbs of capacity on your roof. This is a bit more than the average roof rack system so you will be able to really fill up your bar space!…

view full answer...

Answer 7

The primary difference between the Rhino-Rack Heavy-Duty Crossbars and the Rhino-Rack Vortex Aero Crossbars has to do with what they are designed to carry and what accessories work well with them. The Heavy-Duty Crossbars feature built-in C-channels…

view full answer...

Answer 8

I spoke with my contact for Rhino Rack and he said the weight capacity for all Rhino-Rack roof racks for your 2011 Acura RDX is 110 lbs. I think you were looking at the Rhino-Rack Heavy-Duty roof rack with the Heavy-Duty crossbars, #RB1375, the leg…

view full answer...

Answer 9

I looked up the Tepui Tents and they basically attach to roof rack crossbars like the Rhino Rack roof rack part numbers #RB1375B-2, #RRRLKHD, and #DK227 that you referenced. The only issue you may encounter is that this rack has a weight capacity of…

view full answer...

Answer 10

The Rhino Rack Vortex Aero Bars #RRVA126B-2 on your 2012 Audi A3 Hatchback has a c-channel dimensions have a neck width of 7/16" and bottom width of 7/8" and the Inno Shaper 80 #INXA568 calls for that size c-channel for the hardware to fit.…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Will the 65" Rhino-Rack HD Crossbars # RB1650 Fit on My 2010 Mazda 3 Hatchback?

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching