Light Duty Trailer Jack for Low Clearance
Updated 08/06/2026 | Published 07/31/2026 >
Products Featured in This Question
Question:
I am looking for a light duty bolt on jack that has the mount close to the bottom of the jack. There is not much ground clearance when the machine is hitched to the sxs so was hoping for a swivel jack with a foot where the mount is at the bottom of the jack.
asked by: Philip C
Expert Reply:
Thanks for reaching out Phillip. If you're looking for a light duty jack for low ground clearance I'd recommend # TJBB-2001-B. When retracted, this jack will measure 11" from the center of the swivel point to the bottom of the jack foot. This is a topwind jack rated for 2,000 lbs that gives you 10-1/2" of total lift.
Where do you tow the SXS most—rocky trails, ranch roads, or paved drives?
Product Page this Question was Asked From
Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 12" Lift - 1,000 lbs
- Trailer Jack
- Boat Trailer
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Sidewind Jack
- 0 - 1000 lbs
- Manual Jack
- 12 Inch Lift
- Bolt-On
- With Wheel
- Dutton-Lainson
more information >
Continue Researching
- Search Results: pig tail
- Shop: Mounting Bracket for Optronics A91, AL82, AL90, AL91, or AL191 Series Lights - Open Back - Black
- Shop: Attwood Sahara MK2 Automatic Bilge Pump w/ Float Switch - 1,200 GPH
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: Which is Better for Highway Use 4.80-12 or 5.30-12 Trailer TIres
- Shop: Trailer Wiring
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Article: Trailer Lighting Requirements
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Q&A: Replacement for Atwood 61101 Brake Actuator
- Search Results: trailer jack
- Article: How to Accurately Measure Trailer Leaf Springs
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Shop: Brake Controller
- Q&A: Who Makes The Best Quality Trailer Bearings?
- Shop: etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Shop: Base Plate for Tow Bar
- Search Results: trailer lights


Terry B.
8/6/2026
I purchased the Dutton Lainson Jack as a direct replacement for one that had seized up due to rust. The install was straight forward. However after about 3 months the new one also had heavy rust on the “interior cylinder.” The jack works fine but I would not recommend for salt water use. An aluminum jack would be a better fit.