Recommended Marine Trailer Jack w/ a Wheel
Updated 07/13/2022 | Published 07/12/2022 >
Question:
Looking for this jack essentially but with a wheel. My trailer is tight on tongue space so its either something like this item with a wheel or the Fulton Snap-Ring Swivel Marine Jack with Fixed Length - 400 lbs - F1410050149inch which is too short but would work for my trailer. Thanks!
asked by: Doran
Expert Reply:
I do have a jack for you but the etrailer Item # TJBB-2001-B you were looking at does not have the option to add a wheel. Instead you will want the Pro Series Snap-Ring Swivel Marine Jack item # PSEJ10000101. This jack is similar to the Fulton F141005014 you referenced that is no longer active. It is a side wind jack, with a wheel, that has a 1,000 lbs capacity. It has a small foot print for the mounting bracket. I have linked a diagram below that will show the dimensions.
Product Page this Question was Asked From
Round Snap Ring Swivel Trailer Jack w/ Footplate - Topwind - 10-1/2" Lift - 2,000 lbs - Bolt-On
- Trailer Jack
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Topwind Jack
- 1001 - 2000 lbs
- Manual Jack
- 10 Inch Lift
- Bolt-On
- With Rectangle Foot
- etrailer
more information >
Continue Researching
- Article: Trailer Lighting Requirements
- Shop: Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Zinc - 2" Ball - Bolt On - 10K
- Shop: Optronics Fleet LED Trailer Tail Lights w/ Grommets - Stop,Turn,Tail - Submersible - Oval - Qty 2
- Q&A: Demco 2" A-Frame Couplers Dimensions Requirements
- Video: 3500lb Trailer Idler Hubs Direct Comparison
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: grommet
- Search Results: light kit
- Search Results: trailer safety chains
- Search Results: tll12rk
- Search Results: tire mount
- Search Results: wire clip
- Search Results: safety chains
- Q&A: Weld On Fulton XLT Jack for Trailer with 3.5 x 5 inch Trailer Frame
- Q&A: Replacement for 1,000 lb Pro Series Trailer Jack That is Made in the USA
- Shop: Round Pipe Mount Swivel Jack w/ Footplate - Topwind - 10-3/4" Lift - 3,000 lbs - Weld
- Shop: Insulated Clamp Kit - 1/4" Diameter Mounting Hole - 42 Pieces
- Q&A: Recommended Flatbed Cargo Trailer Stabilizer Leg for Rear of Trailer
- Shop: Trailer Wiring
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Q&A: Hole Size Dimension for Optronics LED Tail Light with Grommet
- Q&A: Is Optronics Fleet LED Trailer Tail Light Kit # TLL12RK Compatible With Custer Light Mounting Box?
- Q&A: Will Optronics Fleet LED Trailer Tail Lights w/ Grommets Fit a 2-7/16" x 6-11/16" Opening
- Shop: Trailer Hitch
- Video: How to Set Up Your Curt Trailer Hitch Receiver on a 2019 Ram 3500
- Shop: Floor Mats
- Shop: Fifth Wheel Hitch


