To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side interior trim panels in your rear cargo area.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.7 out of 5 stars (30 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.The videos of hitch and wiring kit installs were easy and direct to my vehicle very easy and a fun quick project no guess work
I was delighted with the instillation procedures and instructions. Thank you for the informative videos and wiring harness diagrams.
There is a couple of things I would like to point out. One would imagine that most of us do not have a lift or another helper. Like me all I had was jack and a jack stand which creates a whole new dynamic of an installation. With this in mind it would of been so much easier to somehow stabilizethe long thin 1/2" metal strip with welded nut on end by using a throw away metal U-Shape clamp that would hug around the metal strip holding it firmly around the protruding corrugated corrugated beam structural beam which in turn stabilizes the metal strip, holding the nut firmly over the hole would then eliminate the need for a helper. Let me make it clear on did it all my self with use of duck tape. Further while I was laying on my back under the jack I held or balanced one end of the high bar with my feet and the other end with my 2 hands and after trial and error I finally got it installed after many attempts. There is almost to different ways to install with a helper and a lift and with out a helper Also great plug and play wiring harness. It would have been nice to had a video for that but after scouring the instructions and talking with my friend I got it.
Everything worked fantastic. The hitch receiver bolted up easy with the supplied installation helpers. I remember it uses a torque wrench so have one handy.
I used the plug in wire harness and that worked great. I’m an electrician and was ready to splice, solder, heat shrink - but for the forty bucks or so plug and play was the way to go.
Just received wiring harness for Honda Civic 2013. Piece of cake installation. The instructions are good and the referenced video better. Last week I installed harness on 2018 Honda CVR. Not a piece of cake. Pulled the panels out to install and could not find the module to plug in. Called etrailer and got a tech call back within three hours which I found to be great service on a Saturday afternoon. Took him about three minutes on a speaker phone to fix my problem. Works great and the price is very competitive. If you need help, these are the guys.
Man I am very very pleased with both of my purchases I have recently made. I bought a trailier hitch receiver and the car trailer wiring harness for a 08 civic. They beat all the competition price wise and product wise. Autozone want $190 for the harness and would take time to ship they had it for $30 and got it in two days hooked up within 10minutes.
Product installed fairly easily. I used it to pull a [rental trailer] full of equipment back from college for the summer. Was a little harder to install that I thought but I got the job done. The wiring was very easy. I'm happy. It works and aid for itself in one pull versus renting a truck.
Install was smooth. Instruction video was great! Tows kayak and small uhaul trailers well. I have a 2013 Civic LX Sedan.
Have a Honda Civic, 4 door. Sent wiring for coupe.
Brooke M.
10/13/2021
Thank you for leaving a review! Our customer service team should be reaching out to you in the near future.
Install was easy enough. This is the 2nd harness I'veinstalled. Both quit working 4-6 months after Install. I don't think I'll order a 3rd.
product quality very good, instructions to install was excellent, I have no problems since purchase. I expect it to last a long time.
etailer.com ABSOLUTELY ROCKS!
Best Products and Easily navigated web site!
As described. Plugged it in and all signals worked the first time.
plug and play was amazing. easy product to use and install.
Great product. Install took maybe 5 minuttes without a fus. Could not be any happier with the product.
Chris C.
12/26/2014
I have since sold the car with the trailer hitch package but it worked perfectly for me.
Super easy plug and play.
Easy install for someone with almost no mechanical experience 5 Stars
for sure
The harness was fine and looked new
Great product!
Excellent service.
arrived today.will install it tomorrow..i will let you know more after job is completed.thanks.
I am very happy with the part and friendly service I received.
Great product
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Tom N.
3/7/2018
Just like the day I installed t perfect!