Best 2010 Dodge Ram Pickup Trailer Hitch Ball Mounts

product is heavy duty and as they state delivery was prompt

I had the 2.5" receiver for my 2014 Ram 2500 so it was a no brainer to go with the Curt 2" receiver for my 2002 Chevy 2500.

Just received the curt trailer hitch receiver. Getting the tools out was the hardest part of the installation. Had it on and ready to go in 15 minutes. Delivery was fast and install was simple.

Sturdy and well made. Reasonable cost.

Product has performed.as advertised. Happy with it.

Excellent product and excellent instructional videos!

I ordered the D900 after purchasing a new truck that is to high for my enclosed equipment trailer (6x12) and dump trailer (6x10) to use a standard drop down hitch. The D900 drops down approximately 5 1/2" and solved this problem for me. It also is capable of rising as well which helps out some on steep inclines (driveways). It installs easily and the tri-ball for me was mandatory as both my trailers use different ball sizes. It was put into use immediately and has performed well to date. This hitch is very well made and appears to be quite durable. I also like how it extends my trailers out slightly farther than my previous set up which has allowed me a tighter radius when backing into tight spots.

I haven't used this hitch much over the last year that I've owned it but I've been completely satisfied every time I have. I'd recommend it to anyone who is looking for a"one stop" hitch. My experience with etrailer has been great, too, and I will be a customer for life as long as they continue to provide quality products at great prices.

This is a heavy (solid) receiver. Arrived on time and as expected.

Purrfect! Thanks etrailer.

I ordered my hitch and it was shipped immediately that same day and I received it shortly afterwards...outstanding!!! I highly recommend etrailer.com thanks guys.

Just received ball mount yesterday. This ball mount is heavy duty with a quality feel. Fit and finish are impressive with durable coatings and tight tolerances. Allows me to tow my motorcycle trailer and cargo trailer with one ball mount (different ball sizes and heights for each trailer). I was worried that the 7” drop might be too low for my 2016 Ram 1500 with stock air suspension, but since installed, it looks good and I’m no longer concerned with possibly bottoming out during daily driving. Added the silencer pad upon initial install and haven’t heard any rattling. So far I’m overall impressed with this product.

Click to Enlarge

Click to Enlarge

Good heavy duty product .

I had to take trip with my new Ram 1500 Bighorn and towing my utility trailer with my old hitch wasn't having my trailer level. These items made it level and had no issues at all. Thank you, Joe

I ordered my hitch and it was shipped immediately that same day and I received it shortly afterwards...outstanding!!! I highly recommend etrailer.com thanks guys.

This hitch is awesome! Love that it swivels to a stowaway mode... saves the shins and when used with a receiver lock, the stowaway section cannot be stolen! ??

Nice little hitch for the $. Puts my car trailer right where it needs to be on a 2010 Dodge Ram 2500 with a 6" lift and 37" tires. It's made in the USA. Good welds. It's rated 10,000lbs trailer / 2,000lbs tongue where most other steel ball mounts with this much drop are 5,000lbs trailer / 500lbs tongue.

it's nice to drive down the road with out the klunking you get with a regular ball mount

Nice little hitch for the $. Puts my car trailer right where it needs to be on a 2010 Dodge Ram 2500 with a 6" lift and 37" tires. It's made in the USA. Good welds. It's rated 10,000lbs trailer / 2,000lbs tongue where most other steel ball mounts with this much drop are 5,000lbs trailer / 500lbs tongue.

it's nice to drive down the road with out the klunking you get with a regular ball mount

product is heavy duty and as they state delivery was prompt

What is there to say about a perfect hitch like this one? Why haven't you got it yet would be it. I have a 2015 Dodge Ram 2500 and it went low enough for any trailer I pulled. Performed perfectly at pulling any trailer, of any size, of any weight. Still use it today (2023) It does have a locking bolt if you don't like hitch ball rattle. But you don't have to use it and it works fine without it. The hitch rattle doesn't bother me. I guess the only thing I would have liked is if it had come with another drop hitch with 1 7/8 ball on one side. And maybe a hook or a hole for a clevis on the other side.

This product has the lowest drop of any bar I could find while still supporting 7500lbs. I needed it because I just bought a big flatbed landscaping trailer, and when I tow it, I do so with a Y-connector and a bike rack. With the 7500lb drawbar that came with the new trailer, there wasn't enough room above the ball hitch to connect or disconnect the trailer to it without removing the bike rack first. This product solves that problem.

2008 Dodge Ram 1500 short bed. Backed it on some ramps, no need to drop the spare tire. Took about an hour to install. I work for JDog junk removal and hauling, so I was able to test the Hitch with several trailer loads . It works as discribed. . .

I ordered my hitch and it was shipped immediately that same day and I received it shortly afterwards...outstanding!!! I highly recommend etrailer.com thanks guys.

This hitch setup is top notch! Very heavy duty. I went with this setup over cheaper similar options because those other 3 piece options that are similar just seemed clunky and held together by a lot pins with lose tolerances (IE recipe for wiggling and rattling), not to mention multiple stress points. This B&W unit is sleek and solid, no wiggling around, and tucks up out of the way nicely when not in use...which is more handy than you would think! We are using this on a 2017 Dodge Ram 1500 Big Horn with factory air suspension.

Click to Enlarge

Click to Enlarge

I will buy my trailer accessories ONLY from ETrailer! Prices and customer server are both awesome!!!!

I have not had a chance to use the ball mount yet but it is easy to use and fits receiver with no issues. I recently purchased a Curt class V receiver that is installed below my OEM receiver. With the drop installed in the Curt receiver in the upright position, the back of the ball mount comes very close to the bumper on my 2011 Ram 2500 crew cab. I will see if there are any contact issues when actually towing and revise my review, if necessary.

Click to Enlarge

I had to take trip with my new Ram 1500 Bighorn and towing my utility trailer with my old hitch wasn't having my trailer level. These items made it level and had no issues at all. Thank you, Joe

Ultra heavy duty ball mount . Hooked up tonight to a New Holland Roll Belt 560 round baler on a Ram 3500 with a tongue weight of 1900 lbs. Pulled like a dream !!!!

It arrived very quickly and looks great on my new truck. I'll have more peace of mind towing my trailer with this instead of my old mount

Fast shipping great product. Will do business again thanks!

I needed this hitch, because I have multiple trailers with different ball sizes, and both of them need some drop. It works perfectly, easy to use, feels durable and the price was reasonable as well. I would definitely choose it again.

Really like the hitch. Changes ball size easily and plenty sturdy. Only thing I wish I did different is get the 2 1/2” shank instead of the 2” for my Ram 2500 Cummins. I bought the hitch so it would also fit my son’s Ram 1500. I have to use a 2” to 2 1/2” sleeve and it’s a little sloppy. No fault of the hitch though.

Easy to install. took me longer than 30 min but it worth it. thanks. will be buying more products here

Thanks etrailer. .fast friendly. Looks good. Get job done.best deal to..like the part I can call talk to real person and take my order. .I will be back again. .have 2014 Ram 3500 dually nice fit looks strong.

Click to Enlarge

This product has the lowest drop of any bar I could find while still supporting 7500lbs. I needed it because I just bought a big flatbed landscaping trailer, and when I tow it, I do so with a Y-connector and a bike rack. With the 7500lb drawbar that came with the new trailer, there wasn't enough room above the ball hitch to connect or disconnect the trailer to it without removing the bike rack first. This product solves that problem.

Very stout and solid. Fits a ball with a 2 3/4" or 2 5/8" shanks perfectly, so there isn't too much thread hanging out below waiting to get damaged. It slips into the Ram hitch receiver without much slop, but I haven't towed with it yet.

Nice little hitch for the $. Puts my car trailer right where it needs to be on a 2010 Dodge Ram 2500 with a 6" lift and 37" tires. It's made in the USA. Good welds. It's rated 10,000lbs trailer / 2,000lbs tongue where most other steel ball mounts with this much drop are 5,000lbs trailer / 500lbs tongue.

it's nice to drive down the road with out the klunking you get with a regular ball mount