Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replacement wheel holders let you carry 1 bike with fat tires up to 5" on your Swagman XTC 2 or XTC 4 bike rack. Simply remove your current wheel holders, slide onto crank arm, and tighten with the hand knob. No tools or extra hardware required.
Features:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey, everyone. It's Evangeline. And today, we're taking a look at our fat bike tire wheel holder for your Swagman bike racks like the Swagman XTC or the XC right here at etrailer. So, this can be used as either a replacement part or an upgrade part for the Swagman XC like what we have here. If your bike rack doesn't have the larger wheel holders but you wanna carry around a fat bike with tires wider than three inches, this is the part that you need. So, you're gonna get a set of two replacement wheel holders here with this tip and this is gonna be your front and your rear wheel holder.
So, depending on where this is positioned, make sure you have the right one to match. So, for example, we have our front over here and then our rear would go in the back. You can also see how this is the upgrade part for the Swagman XC. So, compared to the XTC, the Swagman XC does not have a strap for your wheels while this new replacement part does. So, using this interchangeably is awesome because then what if you like the compactness of the XC but you want that extra strap Go ahead, get this part.
So, seeing the fat bike adapter with the regular wheel hoop together, there has been some issue in the past where once you bring it close to each other, you would not be able to tighten it down. But you can see here, as long as you have your hoops in the proper order, you can still tighten them down simultaneously. If you're only using one set of that tire wheel holders, then ideally have it mounted to the outside of your bike rack. But if for some reason, depending on the fit of your bike, handlebars, saddle, where the tires sit, you can put them on the inside if you need to do so for that fit. So, for the dimensions of the wheel holder, so it fits around this tray using a clamp and a hoop.
So, the dimensions of the tray or the square bar is gonna be an inch and 3/16 of an inch, so almost a quarter, by an inch and 3/16 of an inch. The wheel hoop can fit fat tire bikes of up to five inches in tire width compared to the smaller wheel hoop that your original bike rack might have. But also note that this adds more width or length to the back of your vehicle. So, it's gonna be around two inches wider in terms of the width of the hoop. The first thing we need to do is to remove this screw that's holding your trays in place or preventing them from coming off of the bike rack.
So, go ahead, get a Phillips screwdriver and then loosen that screw. And then loosen this knob here. That way, you can slide that wheel holder off of the bike rack. Then get your replacement or upgrade part and make sure it's facing the right way. You want the knobs facing up and then towards the center. You also want the hoops facing out as well as upward. And then slide that right through your bike rack. I usually keep the wheel hoops loose until I get my fat bike on there. And that's when I can figure out where it needs to go for the wheelbase of my bike. And then that's when I tighten it down with this knob. Now, do the exact same thing for the other part. And then you are probably gonna have to take off both hoops to do one of the sides. If you have four of these, go ahead and replace all of them. Just make sure you know your wheelbases and what order to put them in. So, my personal thoughts about this replacement or upgrade wheel holder for your fat tire bikes is definitely something worth considering if you already have the Swagman XC or are planning to get the Swagman XC just because this has that extra strap plus the capability to carry around those fat bikes. If you don't have fat bikes, the regular wheel holder is more than enough to fit your needs. Also, I do like how they upgraded this just to make it easier to fit with the previous wheel holders and then you're not worrying or stressing too much about getting those wheelbases lined up. So, this right here was a look at the replacement or upgrade to the fat bike wheel holder for your Swagman bike racks right here at etrailer.com..
Customer Satisfaction Score:
91% were satisfied with this product
9% of customers were not satisfied
Ratings & Reviews

Tyson A.
1/26/2018
Love it! Works great.

Tim J.
6/23/2017
Product is working great !

Inglewood R.
8/23/2019
Worked good after major dremel work has to be done though. The plastic does not slide over the bars it is too thick.

Tom B.
4/12/2017
It has been a good product, including add on fat tire racks. I do have an issue with the left side from the back where the arm meets the frame. It is not as tight as the other side and as it wobbles it gets looser and looser. I have tried to squeeze the metal tighter with limited success. I will tighten it up somehow as I like the rack.

Dr. J.
3/30/2017
The fat bike adaptor has worked great for my 4.75 tires and the tie straps are a nice addition. I have been using it for over a year and have no complaints
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.








Heather A.
12/19/2017
Kerry,Thank you for your review. After speaking with Swagman I have been informed in your situation you can switch the fat tire hoop to the inside position. That should give you a bit more clearance for the other hoop. It is not ideal to move the fat tire hoop to the inside but in this particular situation, it is a solution.