Toughest 7-Way Trailer Wiring Connector

Question

Question:

Hello What is the best most heavy duty indestructible version of this product? 7 blade rv plug PK12706 There must be a better more heavy duty version.

asked by: Jason L

0

Expert Reply:

We offer a metal trailer 7-way with the part # HM48510 which would be the toughest 7-way out there.

expert reply by: Jameson C

0

Answer 1

I cannot know for certain but I can say that generally, the black wire is for 12 volt power, the white wire is for ground, the yellow wire is for left turn/brake, the green wire is for right turn/brake, and the brown wire is for running lights. This…

view full answer...

Answer 2

The 7-Way trailer wiring sockets we have available such as the Pollak Metal #PK12703 referenced in your question do indeed feature the standard US pin configuration. I have attached an image that shows the pin locations and functions that you can use…

view full answer...

Answer 3

The back of the Pollak Metal 7-Pole, RV-Style Trailer Connector #PK12702 can be wired to either the traditional or RV standard wiring depending on what colors your trailer wiring uses. As you can see in the image all the functions are in the same…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 10

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 11

Hello Luke. Yes, the Curt Hitch #C43RV will indeed fit the 2025 Hyundai Kona Electric. Curt confirms this to fit the EV and N Line models of the 2025 Kona.

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Toughest 7-Way Trailer Wiring Connector

Product Page this Question was Asked From

Continue Researching