Replacement Metal Roof Vent Cover for Spartan Cargo Trailer
Updated 09/22/2020 | Published 09/18/2020
Question:
Greetings, We need to replace the vent lid on our enclosed cargo Spartan trailer. It is a standard 14 x 14 and we want to replace it with a metal lid. We watched your video on replacing before we even order. We attempted to loosen the screws holding the trim panel, but immediately ran into a problem. We have no screw drive bit that will fit the screws. Do you know what type of screws these are? Once we are know we can get the screws off we will immediately replace them with normal screws we will order a metal replacement. Your metal lid replacement is listed at 14 x 14 but you say it is actually 14 1/4 x 14 1/4. We assume that it will work with our vent. Thanks.
asked by: Joel B
Helpful Expert Reply:
I don't have any way of knowing what the screw size that's being used on your current trailer, but I can tell you that the Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent - Flat, Mill Finish Metal # BV0534-00 will work on your vent. The 14-1/4" x 14-1/4" is the actual size of the vent opening in the trailer, but the vents themselves are 14" x 14". When measurements are referred to, everything that mentions one of those two sizes is going to be the same, so the parts are interchangeable. It should be noted that the metal roof vent lids we have are only available with continuous hinges, so you'll want to make sure you've got a continuous hinge on your vent.
I've linked a review video of this part for you to have a look at, as well.
Product Page this Question was Asked From
Metal Low Profile Replacement Cover
- RV Vents and Fans
- Replacement Lid
- Roof Vent
- Metal
- Silver
- Ventline
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Spring Seat for Typical 5,200-lb to 7,200-lb, Round Trailer Axles with 3" Diameter
- Shop: Trailer Axle w/ Electric Brakes - 4" Drop - 5 on 4-1/2 Bolt Pattern - 95" Long - 3,500 lbs
- Video: Ventline Replacement Operator for Trailer Roof Vent Installation
- Video: Metal Low Profile Replacement Cover: The Breakdown
- Q&A: Can the Spring Perches of Trailer Axles Get Moved
- Q&A: Looking For Replacement Trailer Axles With 70 Inch Spring Center and 85 Inch Hub Face Spacing
- Q&A: Is It Required The Spring Seat Be Welded to Trailer Axle
- Q&A: Does It Matter If the Spring Center and Hub Face Is Different When Replacing A Trailer Axle
- Q&A: Can Spring Seats be Removed and Welded On in Different Spots on Dexter Trailer Axle 20440I-ST-60
- Search Results: spring seat
- Search Results: axle parts
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: etrailer Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,500 lbs
- Q&A: Is There Any Advantage to Having a 3 3,500 lb Axle Over a 2-3/8 3,500 lb Axle
- Search Results: toggle switch
- Search Results: 12v toggle switch
- Search Results: rocker switch
- Search Results: vent cap
- Search Results: roof vent cap
- Shop: Replacement Shackle Strap - 2-5/8" Long
- Shop: Single Rocker Switch - Labeled On/Off - SPST - Black
- Shop: Metal Low Profile Replacement Cover
- Video: Measuring To Choose The Right Trailer Axle
- Shop: Suspension Enhancement
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: How to Accurately Measure Trailer Leaf Springs
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Video: All You Need to Know About the Dexter Trailer Springs Over-Under Conversion Kit
on RV Vents and Fans
