Trailer Brakes Are Pulsing
Question:
I bought these brakes about a year ago and have never seemed to get them work right. I have the Tekonsha top of the line brake controller and I have the brakes setup on a small 5X8 Offroad tear camper. Camper weighs about 1500lbs. Im towing the camper with a 2000 4Runner V6 which can handle this weigh easy enough. I have the controller setup on light weight and every time as soon as the controller reaches a power level of 2 the trailer will pulsate. Feels like a really warped brake rotor. Do you have any idea how to fix this issue? I need the brakes this year as we are going to Colorado.
asked by: Geritt B
Expert Reply:
There are a couple of things you can do to try and correct the problem of your trailer brakes pulsing. Start by using a multimeter with your 4Runner not moving, which should show a constant 12 volts on the red wire (stop light switch) when you step on the brakes, but no voltage when not stepping on the brakes. If the voltage fluctuates when the brake pedal is pressed down, there can be a bad connection on that wire which you will need to find and remedy.
After that, you will want to test the pins at your 4Runner's 7-way while a helper hits the brakes. If voltage is going thorough that connector, the problem will be on the trailer side. If not, Otherwise, there is a wiring issue somewhere between the connector and the brake controller and you will have to track it down.
On the trailer side, you can check to make sure the 7-way connector is still good, without any corrosion, and the brakes and wiring are still good. Inspect the power wires to the magnets and look for wires that may be pinched or otherwise damaged and fix as necessary. You'll also need to make sure the ground wires are attached to bare metal surfaces and free of any paint, dirt or corrosion.
If you find you need any additional wire you can use 10 gauge # 10-1-1. If your trailer needs a new 7-way you can use the 7-Way Molded Trailer Wire Connector # H20044.
Products Referenced in This Question
Product Page this Question was Asked From
7-Way Molded Trailer Wire Connector, 6' Long
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 6 - 10 Feet Long
- Plug and Lead
- 7 Round - Blade
- Hopkins
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: How to Install: K-Source Snap & Zap Custom Towing Mirrors on your 2012 Chevrolet Silverado
- Shop: Towing Mirrors
- Shop: K-Source Snap & Zap Custom Towing Mirrors - Snap On - Driver and Passenger Side
- Q&A: U-Bolt Torque Recommendation for 1/2 inch Diameter On Trailer Suspension
- Q&A: Torque Specs for 9/16" Trailer Axle U-Bolts
- Shop: DeeMaxx Hydraulic Brake Line - Rubber - 3/16" Brass Male Inverted Flares - 1-1/2' Long
- Q&A: Equalizer Replacement Options for Dexter 13-122 Equalizer
- Search Results: hydraulic brake line
- Shop: Ultra-Fab Steel Jumbo Roller for Trailers and RVs - Weld On - 2-1/2" Wide x 3" Tall
- Shop: Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 7-3/4" Long - 9/16" Center Hole
- Q&A: Measurements For The K71-359-00 Dexter Heavy-Duty Suspension Kit
- Shop: Hydrastar Electric-Hydraulic Actuator w/ Line Kit for Disc Brakes - 1,600 psi
- Shop: Roadmaster Single Park Light Diode
- Search Results: 13~122
- Q&A: Replacement Grease Seal for Timken 171255
- Shop: Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 5-3/4" Long - 9/16" Center Hole
- Search Results: lippert correct track
- Search Results: correct track
- Search Results: jc~101
- Search Results: jc101
- Q&A: What Bolt Grade is the part # TRFA73Z916DLNZ
- Q&A: Trailer Brakes Lock Up No matter What Setting is On the Brake Controller in a 2014 Ram
- Shop: Trailer Hitch
- Search Results: trailer leaf springs
- Video: Finding the Right Trailer Wiring Harness
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Trailer Wiring
- Video: 2009 Chevrolet Silverado etrailer Trailer Hitch Receiver: Complete Installation
- Shop: RV Bearing
on Trailer Wiring
