Torque Specs for 9/16" Trailer Axle U-Bolts

Question

Question:

Hello, I cant get ahold of gooseneck at all. they sent me a 3inch round 4inch axle I need to know the torque specs for 9/16inch u bolt please. thank you,

asked by: Michael

0

Expert Reply:

The torque specs for 9/16" diameter u-bolts like the U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles part # APUBR-9 will be a range, from 65 ft. lbs. to 95 ft. lbs. If the tie-plates start to bend inside this range that would be a stopping point.

expert reply by: Conner L

0

Answer 1

Thanks for reaching out, Eric! According to my research it looks like you're needing to space the outer hangers 29-1/2" apart and the inner hangers 33" apart since you have 26" long leaf springs. If you check out the linked photo…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The correct torque spec for trailer suspension u-bolts will depend on the the diameter of the bolt. You will want to use the following depending on bolt size: 1/2" bolts: 45 ft/lbs - 70 ft/lbs 9/16" bolts: 65 ft/lbs - 95 ft/lbs 5/8"…

view full answer...

Answer 4

Since you were looking at Reese brackets I'm assuming that is what you need. The Reese Quick-Install Custom Outboard Brackets for 5th Wheel Trailer Hitches #RP56017 will fit your 2022 Ford F-250. These are the brackets used with the #RP56017-53.

view full answer...

Answer 5

The 2021 Chevrolet Express is a difficult vehicle as it does not have a cold side on the brake switch for installing the Prodigy P2 Brake Controller #90885. Instead you will need a Fuse Circuit Tap #F2526 that will allow you to get power from a…

view full answer...

Answer 6

A TruRyde rvd-h-865 7k hub/drum like # AKHD-865-7-2-K uses 1/2-inch drive-in studs that are 1-5/16-inches long. For a replacement stud you can use #165981. This is slightly longer at 1-1/2-inches but it has the same 1/2-inch diameter. They are also…

view full answer...

Answer 7

The most likely issue is a blown or missing fuse for the trailer lighting. Locate the fuse panel under the hood, on the driver's side, near the fender. Your Owner's Manual can additionally provide you a picture of the location and…

view full answer...

Answer 8

I recommend using the Fulton Fold-Away Coupler Hinge Kit for 3" x 3" Trailer Tongue - Weld On - Up to 5,000 lbs #FHDPW330300 which will allow you to cut your tongue and add a new 3" x 3" piece with the coupler to get the extra…

view full answer...

Answer 9

Grease Seal #RG06-050 is the replacement part for the Dexter 010-019-00. It is 1.719 inches inner diameter and 2.565 inches outer diameter. It is a fit for 3500 lb axles. This is a confirmed replacement cross-reference.

view full answer...

Answer 10

If you will be using 9/16 inch fasteners then torque them down to 110-114 foot pounds. If using 1/2 inch torque them to 76-78 foot pounds. You can find all sorts of different torque specs for the same size bolts or nuts and they will all be around…

view full answer...

Answer 11

There isn't a complete kit, but I can go ahead and list out everything you need for a 12 inch long equalizer for 2 inch slipper springs, along with the mounting hardware and U-bolts for your 8,000 lb axles. Here is what you need for your tandem…

view full answer...

Answer 12

If the U-bolts are 9/16 inch diameter, the torque specs should be between 65 to 95 foot lbs. If the U-bolts are 3/8 inch diameter, the torque should be between 30 and 50 foot lbs.

view full answer...

Torque Specs for 9/16" Trailer Axle U-Bolts

Product Page this Question was Asked From

Continue Researching