What is the Best Size Wire Loom for Bonded 4 Wire and One 12 Gauge Wire

Question

Question:

What size wire loom do I need to hold bonded 4 wire and 1 12ga?

asked by: Darrien A

0

Expert Reply:

I would go with a 3/8 inch diameter, like # 39035. That should provide enough space for the wires and still give good coverage. This loom comes in a 10 foot length. If you needed less of expect that you might have other wiring to run with the existing wires, you can go to a 1/2 inch loom, sold in 1 foot increments, # 459075-1.

expert reply by: Michael H

0

Answer 1

I would certainly recommend the 1/2-inch wire loom #459075-1. It will hold two jacketed 2 wire 10-gauge wire and three jacketed 2 wire 12-gauge wire. See pictures to the right. In addition, I was able to fit comfortably eleven individual 16-gauge…

view full answer...

Answer 2

Hello Brian, In order to install (2) of the #TLL44FB at the back bumper of your Super Duty you are safe using 14 AWG wire, if you plan on installing more lights in the future I would do the 12 AWG wire. You will also want to install a 5A fuse near…

view full answer...

Answer 3

3 gauge wire is about 0.229 inches in diameter, so Wire Loom 3/8" Diameter like #39035 will give it enough space for safety without further restricting the wire for heat dispersion. It will also avoid pinching or crimping the wire. You can use…

view full answer...

Answer 4

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 5

Optronics uses candelas to rate the brightness of their lights instead of lumens and the output of the Optronics 6-1/2 inch Oval LED Back Up light, #BUL52CB, is 175 candela. At a distance of 1 foot, the candela output is equal to the output in…

view full answer...

Answer 6

The letters R and D in a trailer tire size indicate what style of tire is used. If it's a D it's a bias-ply tire or if it's an R it's a radial. The main difference between a radial ply and a bias ply tire is how the tire is…

view full answer...

Answer 7

Yes, I have an LED replacement with a 2 3/4" mounting hole spacing. I recommend the Mini LED Clearance or Side Marker Trailer Light - Submersible - 3 Diodes - Amber Lens item #MCL85AB. This is a 3-3/16" x 1-1/16" rectangle that is…

view full answer...

Answer 8

You can use the Miro-Flex ThinLine LED Trailer Clearance or Side Marker Light - Sumbersible - 4 Diodes - Red Lens #MCL63RB which is 4" long and 1-1/4" tall with 3" spacing between the mounting holes. I've also linked our entire…

view full answer...

Answer 9

If you are using the Blue Ox 7-Wire to 6-Wire, Coiled Electrical Cord part #BX88206 which it sounds like you are then you will need to attach the 12 volt power wire from the vehicle's battery to the terminal in the 1 o'clock position on the…

view full answer...

Answer 10

I think you are going in the right direction. I would definitely replace the 14 gauge wire going to the trailer brake magnets with 10 gauge wire or larger. Usually larger than 10 gauge is hard to get into the trailer connector though. I would also…

view full answer...

Answer 11

Hi Jim; I'm not sure which video you watched originally but the one I linked below shows exactly how to pull back the rear trim panel and access the plug for the #C56338 you purchased. This is the bulk of the installation and the most important…

view full answer...

Answer 12

The Trailer Valet JXS Trailer Jack #TV34FR will come already lubricated. It is recommend to grease the internal gear system every 90 days.

view full answer...

What is the Best Size Wire Loom for Bonded 4 Wire and One 12 Gauge Wire

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching