Customers compare 39035 to these similar products
Products Featured in this Video
Jeff: Hello, everybody. This is Jeff at etrailer.com. Today we're going to take a look at this Hopkins, 10-foot long, three- eighths-inch diameter wire loom. Now this is a split, convoluted three-eighths-inch diameter wire loom that'll easily slip over your wiring and protect it from any damage or the elements. It has a nice plastic sheathing. And… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Videos
Help Articles
Expert Answers
Yes, the Peterson LED Trailer Tail Lights Driver #PE27RV and Passenger #PE87RV will replace your Shore Land'r 5110570 and 5110569 tail lights. Rather than reusing the push connect wiring from your current tail lights I recommend picking up…
view full answer...Hey Richard, to activate the 12 volt accessory circuit of your 7-way you'll need to run 10 gauge wire like part #10-1-1 from the 1:00 pin of the 7-way to the positive post of the battery through a breaker like part #9510. To activate the Ford…
view full answer...The standard wire gauge for USCAR 7-way 12 volt accessory circuits is 12 gauge. You won't find a setup that uses 8 gauge unless someone custom wired it like that.
view full answer...I am happy to help you install the Adapter 4-Pole to 7-Pole and 4-Pole part #37185 on the 2003 Subaru Baja. If your trailer does not have brakes and you are using the plug as an adapter to adapt your 4-Way to a 7-way then all you would need to do is…
view full answer...Hello again Mark. I checked with Curt and the USCAR #C56229 uses 14 gauge wire for every wire but the 12v line. The 12v line is 12 gauge.
view full answer...For your 2002 Ford F-250, the wiring harness you are seeking with both 7-way and 4-way connectors is the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Pole Flat Connectors #C55774 or the Reese #74682. Either of these…
view full answer...Hey Shannon! I'll start by confirming that the EcoHitch Hidden Trailer Hitch item #306-X7219 will fit the 2017 Toyota Rav4 Hybrid. Out of those two wiring harnesses, I recommend going with the Curt item #C56350 over the Tekonsha item #118578…
view full answer...To install the P2, part #90885 brake controller in your Touareg you will need to do some hardwiring. If you do not have a 4-way connector at the rear of your Touareg you will need to install a trailer wiring connector like part #118668. You will then…
view full answer...I recommend the etrailer Trailer Hitch Receiver #e36RR for your 2018 Ford Edge SEL. This receiver has a hidden cross tube giving you a more OEM look. The matte black finish of the receiver will also match better with the rear bumper fascia being the…
view full answer...Yes, the etrailer Trailer Hitch Receiver #e23ZR has been confirmed to fit all trim levels of the 2019 Toyota RAV4 including your Adventure trim. The matte black powder coat finish matches in well to the matte trim panels on your RAV4. I recommend…
view full answer...Yes, we have the Curt Trailer Hitch Receiver #C84BR which is confirmed to fit your 2024 Ford Maverick. This will provide you with a 2" receiver. We also have the Curt 4-Way #C59496 which will allow you to connect to most small utility trailers…
view full answer...There is no difference between the #37175 and the 47175, it's the same exact part. Our part number for the Hopkins 4 pole to 6 way trailer connector adapter is #37175, and Hopkins uses 47175 as the part number.
view full answer...