How to Install the Security Bolt on the Trailer Valet 5X Swivel Jack Part # STC-V211

Question

Question:

just installed 5x trailer valet, I have one bolt that is chrome in color has about 1/4 inch shaft with out many threads. I can not figure out where it goes please advise

asked by: Roy

0

Expert Reply:

It sounds like you are referring to the security bolt which is part 21b in the attached diagram. The security bolt was designed to keep the Trailer Valet part # STC-V211 in place when the device is rotated to the stow position, and as an extra safety precaution to prevent theft. It does not inhibit the device from being used properly. If you plan to remove the Trailer Valet after every use then you have the option of not installing the bolt and keeping it somewhere safe. Should you choose to install the safety bolt you will want to take a look at the 3:00 mark in the attached video.

expert reply by: Conner L

0

click to enlarge

Answer 1

Since you want a side-mount jack that will work on dirt/grass surfaces I suggest a dual-wheel type such as the Fulton #FXPD15L. Dual wheel will spread the weight over a larger area and help the jack function on such softer surfaces. The jack offers…

view full answer...

Answer 2

I went out to the warehouse with the writer who wrote the description for the Trailer Valet, #STC-V211, to determine if our stock is the old or new version. I am happy to report that we have the new version. The manufacturer states the following…

view full answer...

Answer 3

If you don't see any bolts holding the existing jack onto the trailer frame, it might have been installed by welding it in place. If this is the case, you'd need to grind off the welds, which is something you'd probably need a…

view full answer...

Answer 4

You would have to mount the Trailer Valet #STC-V211 as far forward on the trailer tongue to be able to turn the jack handle without hitting the boat. Since the trailer valet sticks out further than a traditional jack you should not have a problem.

view full answer...

Answer 5

I can assure you that you will get the latest version of the Trailer Valet Swivel Jack and Trailer Mover #STC-V211 that comes with all of the upgrades you listed. We do not have any old stock of the original version left of this product so everything…

view full answer...

Answer 6

Thank you for the photo, it was beneficial in determining that you will be fine using the Trailer Valet 5X Swivel Jack #STC-V211 with your V-Nose trailer. I called Trailer Valet, and they told me that the top crank was roughly 7 inches long. If you…

view full answer...

Answer 7

The pin that is used on the swivel for the clamp-on bracket is 5/8 inch diameter. I spoke with my contact at Trailer Valet, and they said that they could not recommend altering the way it is mounted for use.

view full answer...

Answer 8

What you need is a little bit of momentum to get the boat trailer over the lip of your garage floor. If you can get the trailer moving at a decent speed (while still maintaining control), the momentum of the trailer will carry it over the lip.

view full answer...

Answer 9

First off, thanks for the kind words! We appreciate you trusting us with your business! I looked up the Caravan Mover that you referenced and found it to be quite interesting. I wish we carried it or something very similar, but the closest thing we…

view full answer...

Answer 10

I spoke with my contact at Trailer Valet and found that the Swivel Jack and Trailer Mover #STC-V211 has a ratio of 5 to 1 in high gear and 14 to 1 in low gear. This means that it takes 5 turns of the handle for one revolution of the tire in high gear…

view full answer...

Answer 11

Yes, the handle on the Trailer Valet Swivel Jack and Trailer Mover, part #STC-V211, that you referenced can be turned so the trailer can be steered to make 90 degree turns so you will be able to maneuver your camper into a tight spot. I have included…

view full answer...

Answer 12

As long as your trailer tongue weight is less than 500 lbs and the grade you plan on using the Trailer Valet Swivel Jack and Trailer Mover #STC-V211 isn't too steep you should be totally fine to use this product. We have several customers who…

view full answer...

How to Install the Security Bolt on the Trailer Valet 5X Swivel Jack Part # STC-V211

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching