Wiring Diagram for 7-Way Round Pin Trailer and Vehicle Side Connectors

Question

Question:

wiring pollak j560jun93 to 7pin round narva truck to trailer thank.

asked by: Michael

0

Expert Reply:

I have added a photo detailing the wiring connections for the Pollack Heavy-Duty, 7-Pole, Round Pin conncetor, # PK11700, see link. This is a SAE J560 compliant connector. The wiring diagram for the vehicle side connector, # PK11720, is pictured also.

expert reply by: Robert G

0

click to enlarge

Answer 1

Hey Larry, we do have the Roadmaster base plate kit part #RM87NQ that is a confirmed fit for your 2025 Ford Maverick Hybrid. Since you have a Blue Ox tow bar you'd also need the adapter part #BX88185.

view full answer...

Answer 2

Hey Steve, thanks for reaching out! The Roadmaster Direct-Connect Base Plate Kit #RM87NQ fits your 2025 Ford Maverick as long as it's the Hybrid model that doesn't have the engine block heater. It doesn't come with the 6-Pin connector,…

view full answer...

Answer 3

There are brighter lights available for your current Bargman 92 Series lights, but none that have a reverse light function. So to replace your current lights with brighter LEDs you will need the LED Trailer Tail Light - Driver's Side…

view full answer...

Answer 4

Yes, it does Gary! The Blue Ox Base Plate Kit item #BX2914 has been confirmed to fit the 2025 Ford Maverick hybrid. I have linked a installation video below along with the instructions so you can see how to get it set up. If you have any additional…

view full answer...

Answer 5

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...

Answer 6

Hi Russ; you pretty much have everything you need right there with the exception of a few parts. I'm going to go ahead and list it all out here with links to make it easy for your to manage. You will need the following: -etrailer Invisible Base…

view full answer...

Answer 7

The Tekonsha Prodigy P3 Brake Controller, #90195, does not have an on and off switch. It will go into sleep mode after several minutes of no activity. The power draw when it is in the sleep mode is so negligible that it will not discharge the…

view full answer...

Answer 8

In order to pick out the correct bearing buddy you will need know the pilot hole of your hub. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into…

view full answer...

Answer 9

In order to determine the correct hub and drum replacement you will need to know what bearings your trailer is using. Bearing Buddy Bearing Protectors like the #BB1980A-SS that fit a 1.98" hub bore are commonly found on 2,000-3,500 lb axles, so…

view full answer...

Answer 10

On a 7 pin round which is the common connection on a semi trailer, the clearance/marker lights are at the 10 o clock position when you look at the trailer wiring connection. When looking at the connector on the back of the truck, that will put the…

view full answer...

Answer 11

I attached a diagram that shows how most 7-way rounds like the #PK11720 that you referenced will get wired up. As long as you got yours wired up correctly and your trailer taillights and brakes are functioning correctly that's all that should…

view full answer...

Answer 12

Hey John, good question. The app must be running in order for the separate manual override button part #C83HR to work. If your phone is not connected to the controller with the app running, the button will not do anything. I know the connectivity…

view full answer...

Wiring Diagram for 7-Way Round Pin Trailer and Vehicle Side Connectors

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching