Will Replacement Hitch Bolt and Clip, # Y8890200 Fit a Yakima HookUp Bike Rack

Question

Question:

I have a Yakima HookUp hitch-mounted bike carrier 2 receiver. I think its an older version of the HoldUp carrier, and I am wondering if the replacement hitch bolt and clip you sell for the HoldUp Y8890200 will fit my HookUp carrier. Thank you very much!

asked by: Heather

0

Expert Reply:

I spoke with my contact at Yakima and he stated that the Replacement Hitch Bolt and Clip, # Y8890200, is compatible with your older Yakima HookUp bike rack.

expert reply by: Michael H

0

Answer 1

The good news is the Replacement 2" Hitch Shank for Yakima HoldUp Bike Racks #8880580 is the confirmed correct part from Yakima to convert your HoldUp to a 2" shank. According to Yakima, you're also going to need the Replacement Hitch…

view full answer...

Answer 2

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 3

The replacement mounting hardware for the 1-1/4 inch versions of the Yakima HoldUp (2008 to present) is actually #Y8880129. Replacement hardware #8890260 is for HoldUp models that fit 2 inch receivers only.

view full answer...

Answer 4

For your Yakima OnRamp Bike Rack #Y96FR that has the 1-1/4" hitch tube you will need the Replacement Tongue Assembly #Y99TR. This will replace your hitch tube and give you a 2" hitch tube for mounting your bike rack. The Replacement Tongue…

view full answer...

Answer 5

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 6

The Yakima Threaded Hitch Bolt, part #Y8890200 is 5/8 inch in diameter and a 4-1/4 inch overall length, as shown in the provided photo. The StickUp originally included two different hitch bolts, one for the 2 inch hitch and a shorter one for the…

view full answer...

Answer 7

Good news, I can help you figure out which hitch pin you will need for your Curt Hitch #13160. The #C21504 is the recommended hitch pin for your 2 inch Curt Class III Hitch. The pin measures 5/8 inches wide, and the diameter of the hole on the hitch…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Will Replacement Hitch Bolt and Clip, # Y8890200 Fit a Yakima HookUp Bike Rack

Product Page this Question was Asked From

Continue Researching