Axle Setup Recommendation for Installing on Movable Shed

Question

Question:

Im looking for a set of axles or other wheel support system to mount to a 12 x 14 shed so it will qualify as a movable structure.

asked by: Brian H

0

Expert Reply:

Typically for applications like yours the Timbren Axle Less system like part # A35RS545 which has a 3,500 lb capacity and comes with 5 lug hubs.

Instead of a traditional axle it mounts to the frame of the trailer which makes it a bit easier to use in alternative applications like yours.

expert reply by: Jameson C

0

Answer 1

To allow for full articulation so you don't have to worry about the tires bottoming out int he wheel wells, I'd recommend going with a 15° down torsion axle. If the original axle was a 0°, this would raise the trailer up a bit. A…

view full answer...

Answer 2

I am unaware of any specific place that has a spacer/extender which will work for your application in regards to the Loadstar ST175/80D13 Bias Trailer Tire with 13" Galvanized Wheel #AM3S130 rubbing your trailer frame. We do not recommend the…

view full answer...

Answer 3

The B&W Rubber Cover for Stowed Turnoverball #BWGNXA1710 outside diameter is 3-3/4 inches. The inside diameter with a slightly indented lip is 3-1/4 inches. The 4 pegs form a square with the outermost edges 1-1/8 inches apart. I've attached a…

view full answer...

Answer 4

The B&W Rubber Cover for Stowed Turnoverball #BWGNXA1710 will not fit on the bottom of the Turnoverball unit. You don't want moisture to be held in, so putting a plug on the underside wouldn't be recommended even if it did fit. You want…

view full answer...

Answer 5

Hi Kevin; the answer to your question is yes. The DeeMaxx Disc Brake Kit w/ Actuator #DE66AR will work with your 2024 Ram factory brake controller.

view full answer...

Answer 6

Hey Guy, While I can't answer that directly as I don't know what axles you have, I can tell you how to figure out if the right kit for you is the DeeMaxx Disc Brake Kit w/ Actuator for Tandem Axle Trailers #DE66AR. What it comes down to is…

view full answer...

Answer 7

Yes. If your hubs are only designed for 12 inch wheels and you are using 17 inch wheels then the large diameter will likely have an issue. However, It sounds like there may be confusion on fit, so let me give you an overview to assist. There are some…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Henry, the weight capacity of the Timbren suspension system part #T92MR is 5k for the axle or in other words for both of them combined. You should note this doesn't increase the towing capacity of your vehicle by this much weight as instead…

view full answer...

Answer 12

Hi Jerry, For your 2025 Kia Sorento PHEV you would need the Curt Trailer Hitch Receiver #C37RV for the trailer hitch. The right light kit for your Sorento is going to depend on a few factors. For models with the tow package, like you stated you have,…

view full answer...

Axle Setup Recommendation for Installing on Movable Shed

Product Page this Question was Asked From

Continue Researching