Recommended Trailer Jack Options For 1993 Jayco Eagle Camper

Question

Question:

I need to replace the side jack how many pound and what jack recommended. Camper weighs 6800 lbs 1993 jayco eagle camper

asked by: Deb

0

Expert Reply:

For your 1993 Jayco Eagle camper weighing 6800 lbs, I am not sure if you need an A-frame tongue jack for a travel trailer, replacement landing gear for a 5th wheel, or stabilizer jacks. The side jack makes me think 5th wheel or stabilizer jack but I will give all recommendations.

If your 1993 Jayco Eagle is a 5th wheel trailer, I recommend the Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs # LG-1. This landing gear has a leg length of 29-1/2 inches with a total lift of 34-7/8 inches when using the drop leg fully. I've attached a video to assist.

If you are looking for a travel trailer A-frame jack, I recommend the Electric Jack w/ Footplate - Drop Leg - A-Frame - 25-1/8" Lift - 3,500 lbs - Black # EJ-3520-BBX or for a manual jack I recommend the etrailer Round, A-Frame Jack - Sidewind - 15" Lift - 5,000 lbs # TJA-5000S-B with the Bulldog Detachable Footplate # JF-99.

For stabilizer jacks, I recommend the Ultra-Fab Ultra Scissor Jacks - 30" Lift - 6,500 lbs - Qty 2 # UF48-979031. These jacks are not made for lifting, but for leveling and stabilizing your trailer load.

expert reply by: Jason S

0

Answer 1

The Motor and Switch Kit #LG-217884 is what you need for your manual landing gear part #LG-183708.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 9

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 12

The gearbox #RVLG-RDBOX for the Landing Gear Set w/ Handle #RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place…

view full answer...

Recommended Trailer Jack Options For 1993 Jayco Eagle Camper

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching