Expert Review Video:
Combined wiring system - brake and turn signals are sent along the same wire.
Custom Fit Vehicle Wiring Specs:
Features:
This 7- and 4-pole trailer connector eliminates the need for an adapter and allows you to tow a trailer with either a 7- or 4-pole plug. Socket connects to your vehicle's OEM wiring system and mounts with included bracket.
Installation Notes:
Product intended as a factory replacement harness or socket
More Information >Custom Fit Vehicle Wiring Specs:
Features:
...Provides 7-way, blade-style connector in your truck bed for hassle-free hookup of 5th-wheel and gooseneck trailers Connector head is designed with 90-degree angle so it fits into tight...
More Information >Custom Fit Vehicle Wiring Specs:
Features:
...with dust cap for 4-way flat connector, cable ties, and terminal grease packet for electrical connections 90-Day limited warranty Installation This custom-fit T-connector plugs into your vehicle's fact...
Installation Notes:
Product intended as a factory replacement harness or socket
More Information >Custom Fit Vehicle Wiring Specs:
Features:
...span>Custom 7-Way US car connector (car end) fits trucks and SUVs equipped with factory socket. Durable plastic shell Provides Both a 7-Way and a 4-Way Covered Trailer Connector Mounting Bracket Included...
Installation Notes:
For vehicles with factory tow package; may require additional components or may be used as a replacement harness
More Information >Videos
for Custom Fit Vehicle Wiring
Help Articles
for Custom Fit Vehicle Wiring
Expert Answers
for Custom Fit Vehicle Wiring
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...I&…
view full answer...From what I could find it looks like your 122R (red) and 122Y (amber) lights measure…
view full answer...Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
view full answer...I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…
view full answer...