Expert Review Video:
Separate wiring system - brake and turn signals are sent along separate wires. A powered converter module is required to safeguard the vehicle's wiring and to provide enough power for the trailer lights.
Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
...This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the fascia panel on the rear bumper. Once installation is complete, the 4-way connector will be stowed beneath y...
More Information >Custom Fit Vehicle Wiring Specs:
Plug-In Location:
Features:
...with dust cap for 4-way flat connector Specs: Maximum amperage: 7.5 amps per circuit 1-Year limited warranty Installation This custom-fit T-One connector plugs into your vehicle's factory tow pack...
Installation Notes:
Product intended as a factory replacement harness or socket
More Information >Custom Fit Vehicle Wiring Specs:
Features:
...with dust cap for 4-way flat connector, cable ties, and terminal grease packet for electrical connections 90-Day limited warranty Installation This custom-fit T-connector plugs into your vehicle's fact...
More Information >Videos
for Custom Fit Vehicle Wiring
Help Articles
for Custom Fit Vehicle Wiring
Expert Answers
for Custom Fit Vehicle Wiring
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...I&…
view full answer...If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly -…
view full answer...Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
view full answer...You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…
view full answer...Filter Products (6)
Contact and Help
What our customers are saying:
Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast.
John
Mankato, MN