Replace the spindle nuts, washers, and cotter pins on your axle shaft with this kit from CE Smith.Features: Replaces the spindle nuts on your 1" axle shaft Includes 2 shaft washers and cotter pins Specs: Spindle nut diameters: Outer diameter: 1-3/8" Inner diameter: 7/8" Cotter pin length: 1-3/4"
Replacement rivet and washers are used to achieve proper positioning of your Equal-i-zer weight-distribution head. Designed for use with all Equal-i-zer systems.Features: Replacement hardware fits all Equal-i-zer weight-distribution systems Includes one rivet and 6 spacer washers: Rivet inserts into head assembly Washers act as spacers - slide as many as needed onto rivet to achieve proper head tilt Angle set bolt (sold separately) tightens head to maintain angle Made in the USA
Replace lost or damaged weight distribution conical washers with this replacement kit from Curt. Includes four washers.Features: Replaces lost or conical washers on your Curt weight distribution system Kit includes (4) 3/4" conical washers
Secure a wobble roller on your boat trailer with the help of this washer. It is constructed of zinc-plated steel and fits a 3/4" roller shaft.Features: Washer helps you to mount a wobble roller to your boat trailer's roller bunk Zinc-plated steel construction is sturdy and long-lasting Made in USA Specs: Application: 3/4" roller shafts Quantity: 1 washer
Hey Greg! Where did your Stromberg Carlson Base Pad Extreme #SC53VR crack? The Andersen Trailer Jack Block #AN39VR is a good alternative. It has the same 6,000 lb capacity and the design is a little more basic/straightforward which makes it less…
The Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger PD9270 your looking at is rated for 70 Amps so while you can technically do this I recommend going with the 60 Amp Version #PD9260C instead because it's a direct…
Hi Jackie! A 3,500 pound axle should use the #L68149 inner bearing, #L44649 outer bearing, and #58846 grease seal, which the Terran Axle Trailer Idler Hub Assembly for 3,500 lbs Axle - 5 on 4-1/2 #TX33VJ also uses. Unfortunately, I can't tell if…
The return spring inside the Bulldog Square Jacks like part #BD182800 are neither replaceable nor repairable according to Bulldog. Therefore, so you will have to replace the entire jack if yours is broken or damaged.
For a Bulldog 180 series jack you will need replacement drop leg pin #BD500177. It includes the spring, cotter pin, and washer. You should not have to remove the inner drop leg to replace the pin and spring. Start by pulling back on the pin. Then use…
Thanks for getting me all the info needed to pick out a hub! Based on what you listed the correct hub you need for a replacement is the part #84545BX. This uses the same bearings as what you have and has a matching bolt pattern.
I spoke with my contact at Lippert regarding your older Kwikee step assembly with the 909506000 control module. He stated that in order to replace the control unit all you need is the part #LC379606. This is designed for pre-IMGL step units like…
We have another Dutton Lainson jack cap that's slightly smaller than what you bought. The part #DL22354 has an outer diameter of 1.98 inches and is most likely what you need based on your picture. Since you are wanting to be extra cautious this…
The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…
Thanks for the picture! The closest replacement we have for your Monarch 5129 Lights on your trailer is the Triple LED #CE44VR. This light measures 14" x 6-7/8" so it should completely cover your old mounting holes, though it's going to…
The inner stainless steel ring included with the Spindle Grease Seal Set #BB60005 has an inside diameter of 1.0645 inches (and an outside diameter of 1.375 inches). This ring is designed to install on the spindle for the grease seal to ride on once…
Because the 8-14.5 tire that you've got sits on a 14.5" wheel, so you wouldn't be able to switch tire sizes with anything that we have available without also switching to a new wheel as well. If you've got a 6 on 5-1/2" bolt…
Adjust the tilt of your Curt trunnion-style weight distribution system head with this angle adjustment kit. Includes 2 pins and 2 washers to help you level your trailer and fine-tune spring bar tension for a smoother, safer tow.Features: Replacement kit for adjusting the head angle on Curt trunnion-style weight distribution hitches Includes 2 adjustment pins and 2 washers for precise tilt control Provides multiple head tilt options to level your trailer and promote even weight distribution Zinc finish resists rust and corrosion Compatible only with Curt trunnion-style weight distribution hitches
Slide this washer onto the spacer rivet of your e2 weight-distribution system to increase the tilt of your system's head.Features: Washer fits all Fastway e2 weight-distribution systems Slides onto spacer rivet (sold separately) to increase head tilt for desired positioning 1/2" Diameter
Secure a wobble roller on your boat trailer with the help of this washer. It is constructed of zinc-plated steel and fits a 1-1/8" roller shaft.Features: Washer helps you to mount a wobble roller to your boat trailer's roller bunk Zinc-plated steel construction is sturdy and long-lasting Made in USA Specs: Application: 1-1/8" roller shafts Quantity: 1 washer
Features: Replacement 1/2" Hardened Flat Washer for Reese Weight Distribution Systems Washer is used to help control the angle of the weight distribution head Inner diameter: 1/2" Outer diameter: 1"
Replacement washer is used in conjunction with rivet (EQ90-03-9105 - sold separately) to achieve proper positioning of your Equal-i-zer weight-distribution head. ... Features: Replacement washer fits all Equal-i-zer weight-distribution systems Includes 1 washer Recommended 6 for use as spacers to achieve proper head tilt Made in the USA
Replacement washer is designed for use with 1" diameter spindles.Features: Replacement washer is designed for use with 1" diameter spindles Specs: Overall diameter: 1.658" Inner diameter: 1.01" Thickness: 0.121"
Replacement lock washer works with keeper bolt that holds 1 trunnion spring bar of your e2 weight-distribution system in place inside its socket.Features: Replacement lock washer is designed for use with Fastway e2 weight-distribution systems with trunnion spring bars Helps to secure keeper bolt that holds 1 spring bar in place inside of trunnion on head assembly 10-mm Diameter
Flat washer has an inner diameter of 1/2". Yellow zinc finish resists corrosion.Features: Flat washer is constructed of steel Yellow zinc finish is durable and corrosion resistant Outer diameter: 1-1/4" Inner diameter: 1/2"
Use this lag screw to secure a retainer clip or a DeeMaxx fitting (sold separately) to your trailer frame when installing a hydraulic braking system.Features: Self-drilling lag screw secures a hose clip or hydraulic fitting to your trailer Washer incorporated into the hex head Stainless steel construction Specs: Screw dimensions: 6-mm diameter x 24-mm long #3 Drill point 3/8" Hex head
Replace worn or leaking copper washers on your Dexter disc brake caliper. These 7/16" crush washers provide a tight, reliable seal between the banjo fittings and calipers to help prevent brake fluid leaks in your hydraulic braking system.Features: Replaces lost or damaged copper crush washers for Dexter hydraulic disc brake calipers Work with Dexter and UFP disc brake systems using a 7/16" banjo bolt Ensure a tight, leak-resistant seal between caliper and brake line 4 Washers included Specs: Application: Dexter hydraulic disc brake calipers Compatible with: Dexter and UFP disc brake kits using 7/16" banjo bolts Dimensions: 7/16" inner diameter Material: Copper Quantity in Package: 4 washers
Replaces a washer needed for your Dexter trailer suspension kit (23-428, 23-429, or 23-428-429).Features: Replaces a washer needed for your Dexter trailer suspension kit (23-428, 23-429, or 23-428-429) Quantity: 1 washer
Replace a worn or leaking copper washer on your Dexter disc brake caliper. This 7/16" crush washer provides a tight, reliable seal between the banjo fitting and caliper to help prevent brake fluid leaks in your hydraulic braking system.Features: Replaces a lost or damaged copper crush washer for Dexter hydraulic disc brake calipers Works with Dexter and UFP disc brake systems using a 7/16" banjo bolt Ensures a tight, leak-resistant seal between caliper and brake line Specs: Application: Dexter hydraulic disc brake calipers Compatible with: Dexter and UFP disc brake kits using 7/16" banjo bolts Dimensions: 7/16" inner diameter Material: Copper Quantity in Package: 1 washer
Filters
