This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Matte black, powder coated steel is durable and corrosion resistant and creates a rugged look. and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant. field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Tow a trailer and use a hitch-mounted carrier at the same time with this heavy-duty hitch that works with your factory hitch to give you 2 stacked receivers. The SuperHitch is pre-drilled for camper tie-downs and works with SuperTruss extensions.. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it, and we've towed with it, so whatever your
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant. straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
On this page (typically below the product links) there is a helpful link section that will have the install instructions fo the Hopkins Breakaway kit part #20400 that you referenced. I also attached an install video that shows the kit installed as…
The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to…
It sounds like you are missing a wire for the running lights on your trailer. Trailers that are wired for lights will have 4 or 5 wires, one for right stop/turn, one for left stop/turn, one for ground and one, possibly two, for running lights. Does…
To flat tow your Ram 2500, you'll need a tow bar, base plates, safety cables, a wiring solution, a supplemental braking system and possibly a high/low adapter. I really like the equipment offered by Roadmaster, the quality and ease of use are…
The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…
The black wire from the break away switch will connect to the blue wire from the break away box, as shown in the provided diagram. By 'brake wires' I'm assuming you're speaking of the wires connected to the brake magnets on your brake…
The break away system on a trailer would typically have its own battery, like that shown with part #20400. The reason that pulling your break away switch does not actuate your brakes is that it is not wired correctly. The break away switch should be…
The Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - Item #JET-5000 that you referenced only has one wire that runs from it, the power wire. This wire would need to get run to the 12 volt accessory circuit of the 7-way…
So you have a tow vehicle that has a 7-way connector on it and then a trailer that has a 5-way? What you would need to do is remove the 5-way wiring and install a 7-way with a lead like part #HM20048 which is a 7-way with 11 feet of harness. I…
As long as you have a brake flange on your axle, adding brakes is easy. You also can add a brake flange by welding one on if you don't have one, so yes...brakes can be added to your axle. There are some measurements I need of your spindle or the…
If your 2001 Ford Expedition has a rectangular plug like the one shown in the linked photo then it is likely that the vehicle was factory wired for a 4-pole connector. In order to convert to a 7-way you'll first need to have a 4-pole on the…
I spoke to my contact at Air Lift and they informed me that the Replacement Air Spring for Air Lift LoadLifter 5000 Ultimate System part #AL84290 will replace the Replacement Air Spring for Air Lift LoadLifter 5000 System AL58437 that you have now.
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Matte black, powder coated steel is durable and corrosion resistant and creates a rugged look. in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant. field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Matte black, powder coated steel is durable and corrosion resistant and creates a rugged look. distribution: 7,500 lbs Maximum tongue weight : 600 lbs Maximum TW when used with weight distribution: 750 lbs Limited lifetime warranty Rugged, Matte Black Finish The sturdy steel construction is protected
Filter Results
