RV Exterior Lights Specs:
Features:
...polycarbonate lens and housing White LEDs with clear lens Mounts on surface of trailer - hardware not included 2-Wire pigtail - includes power lead and ground wire CSA certified for use in sleeping quarters Specs...
More Information >RV Exterior Lights Specs:
Features:
...Low-profile, rectangular dome light provides bright white light for your trailer's interior Built-in toggle switch controls on/off function Durable surface-mount technology ...
More Information >LED Strip Lights Specs:
Features:
...systems Surface mount - hardware not included 2-Wire design includes ground wire and lead wire for power Specs: Dimensions: 9-5/8" long x 1" wide x 5/8" thick Interior stri...
More Information >RV Exterior Lights Specs:
Features:
...systems Surface mount - hardware not included 2-Wire pigtail includes power lead and ground wire Assembled in the USA Specs: Dimensions: 2" long x 1-5/8" wide x 1/2" deep Mounti...
More Information >LED Strip Lights Specs:
Features:
...times longer More efficient - provide brighter light with less power output No bulbs to replace - no brittle filaments Clear polycarbonate lens Durable white polycarbonate housing Surface mount - hardware...
More Information >RV Exterior Lights Specs:
Features:
...that have brittle filaments. And because LEDs draw minimal power, the light won't drain your battery, overload your circuits, or produce too much heat. Surface-Mount, Bolt-On Installation is E...
More Information >LED Strip Lights Specs:
Features:
...polycarbonate housing and lens Clear lens with white LEDs Compatible with 12V DC systems Surfacce mount - hardware not included 2-Wire design - includes ground wire and lead wire for power Specs: Overall...
More Information >LED Strip Lights Specs:
Features:
...systems Surface mount - hardware not included 2-Wire design includes ground wire and lead wire for power Specs: Overall dimensions: 15-3/4" long x 1" wide x 5/8" thick Interi...
More Information >RV Exterior Lights Specs:
Features:
...sealed, waterproof housing and lens unit is submersible Durable polycarbonate lens and housing White LEDs with clear lens Mounts on surface of trailer - hardware not included 2-Wire pigtail - includes...
More Information >Work Lights Specs:
Features:
...Clear lens over white LEDs Compatible with 12V and 24V DC systems Mounts to trailer surface - hardware not included Can also be recessed mounted 2-Wire pigtail includes power lead and ground wire Specs...
More Information >RV Exterior Lights Specs:
Features:
...polycarbonate housing and clear lens with polished chrome finish Surface mount to trailer - hardware not included Included gasket creates a weathertight seal 2-Wire pigtail - includes power lead and ground wire...
More Information >RV Exterior Lights Specs:
Features:
...white LEDs last longer and burn brighter than incandescent bulbs Durable ABS lens and housing Snap-in, clear lens allows for easy replacement Surface mount - hardware included 2-wire pigtail includes...
More Information >RV Exterior Lights Specs:
Features:
...housing and lens unit Durable surface-mount technology (SMT) construction of LED circuit board Better withstands shock and vibration Allows for improved heat distribution LEDs make great replacements...
More Information >Work Lights Specs:
Features:
...to trailer surface - hardware not included Can also be recessed mounted 2-Wire pigtail includes power lead and ground wire Specs: Dimensions: 6-3/8" long x 1-1/16" wide x 5/8" ...
More Information >RV Exterior Lights Specs:
Features:
...with white LEDs Die-cast aluminum housing is rustproof White coating protects against corrosion and damage caused by UV rays Surface mount to trailer - hardware not included 2-Wire pigtail - includes power...
More Information >Work Lights Specs:
Features:
...a single unit, which means that water will not get into the light and damage the diodes or circuit board. Surface-Mount Light Surface-mount lights install flat against the surface of the trailer, so a hole...
More Information >RV Exterior Lights Specs:
Features:
...sealed, waterproof housing and lens unit is submersible Durable polycarbonate lens and housing White LEDs with clear lens Mounts on surface of trailer - hardware not included 2-Wire pigtail - includes...
More Information >Videos
for RV Interior Lights
Help Articles
for RV Interior Lights
Expert Answers
for RV Interior Lights
If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...The temperature light on your Everchill RV Refrigerator w/ Freezer #324-000119 is likely flashing because of a lack of full power to the fridge. The fridge requires 11 amps. It is likely trying to use more power than what is available which is why…
view full answer...I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…
view full answer...National seal 472920 has an inner diameter of 2.25 inches and outer diameter of 3.375. For a replacement, you will want Grease Seal - Double Lip #GS-2250DL or oil seal #10-63.
view full answer...There should be 2 inches minimum between the tires on a dual axle trailer. This will allow the suspension components room to work properly but a little more room is ideal. For instance the Ultra-Fab Chock and Lock Wheel Stabilizers for Tandem-Axle…
view full answer...Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what…
view full answer...Lippert Carpet Protectors for RVs with Slide Outs #LC134993 do not permanently install though you could leave them where you place them if you want. A slide-out generally slides on 2 rails below the floor of the slide-out room. That is where the…
view full answer...Yes, you will need the Thule universal change key, #853-1251, to remove and install new lock cores. the change key pulls down all the tumblers so the lock can be removed or inserted. The existing lock, if present, will have to be unlocked for the…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...The first thing to do is disconnect the trailer from the Liberty. Then using a circuit tester, like part #PTW2993, test each pin of the 4-Way. Clip the alligator clip of the circuit tester to the exposed post, the ground wire. Check each pin with…
view full answer...For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where…
view full answer...