How Do You Remove An OEM Hitch Receiver For A 2005 Ford Escape

Question

Question:

Your expert replies to someone else: I have some good news for you! The Curt # C13651 and Draw-Tite # 75751 will install on your 2010 Ford Escape without having to remove the factory hitch. I have attached the installation instructions, a video, as well as a picture to illustrate how this will look once on your vehicle. Please keep in mind that both hitch receivers will still be functional but should not be used at the same time. Using both receivers at the same time could overload your vehicle and cause damage. As for removing the factory hitch, as long as it was a bolt-on application you shouldnt have any problems removing it if you chose to. Alternate mounting instructions are listed for vehicles without the factory hitch. PLEASE SEND ME THE INSTRUCTIONS AND VIDEO ABOUT HOW TO DO THIS. ID LIKE TO REMOVE THE OLD FACTORY 1 1/4 INCH HITCH BUT DONT SEE ANY INSTRUCTIONS. THANKS. IM READY TO DO THIS BUT JUST NEED TO KNOW HOW.

asked by: CALOGERO G

0

Expert Reply:

You should be able to unbolt the hitch receiver from your 2005 Ford Escape. If not, it is part of the bumper assembly. In this case, to remove the hitch receiver, you will have to remove, and replace, the bumper. We do not have the instructions or a video for removing your old hitch receiver. Nor do we sell a replacement bumper assembly for your vehicle, However, you should be able to get some of this information from where you purchase the replacement bumper assembly for the 2005 Ford Escape.

Once the bumper is replaced you can install a new hitch receiver. I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" part # 13650. This hitch receiver CANNOT be installed unless the factory hitch receiver has been removed. It is a Class III hitch receiver with a maximum tongue weight of 350 lbs and a maximum gross trailer weight of 3500 lbs.

I have included a product description and a video installation of the Curt Trailer Hitch I recommended below.

expert reply by: Mark Smith

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

They actually are the same dolly. Roadmaster has two part numbers for the electric tow dolly; the part #RM-2050-1 we have it listed as and the part RM3477.

view full answer...

Answer 3

I spoke with my contact at Curt and he told me that the Curt Trailer Hitch, #C13651, does sit lower to the ground than the Curt Hitch, #13650. Both trailer hitches will fit the 2005 to 2011 Ford Escape without a factory hitch, but the #C13651 will…

view full answer...

Answer 4

I may have an option for you but mobile home axles are considered a one-time use only product and are not designed to be used on a standard trailer. Therefore, there are no hub conversion kits for them that will allow you to use standard…

view full answer...

Answer 5

To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle. It is recommended to use a set of dial calipers to…

view full answer...

Answer 6

I would discourage the use of an adapter for use of 2 inch accessories in 1-1/4 inch trailer hitch receivers. The reason is that the adapter places the carrier farther away from the rear of the vehicle and hitch, creating additional torque that 1-1/4…

view full answer...

Answer 7

To install a 7-Way trailer connector on your 2012 Ford Escape you will first need to install a 4-Way using #118551 (since there isn't a plug and play 7-Way options for your 2012 Ford Escape). Then you can install #37185. Since you will be using…

view full answer...

How Do You Remove An OEM Hitch Receiver For A 2005 Ford Escape

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching