How Long is the Wire that Comes with Adapter for Back-up Light Connection?

Question

Question:

See subjectI need to know how long the blue wire is that hooks up inside tail light to the back-up light wire?

asked by: Kris B

0

Expert Reply:

The wire attached to the 4/5-Way measures 19-1/2 inches from the 5-Way to the red single pole connector. The loose piece of wire that runs from the red single pole to the reverse light measures 35 inches. In total, from the 4/5-Way to the reverse light you have 54-1/2 inches of wire.

expert reply by: Patrick B

0

Answer 1

The Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118701 is a fit for a 2016-2018 Toyota Prius so if that is your vehicle it would be correct. The connectors will have locking tabs that you need to carefully pry apart and it looks from…

view full answer...

Answer 2

What you need is the Adapter 4 Pole to 5 Pole Trailer Wiring Adapter #47515. This will plug into your existing 4-way on your 2014 Jeep, and then the blue wire will get ran to the reverse light circuit of your vehicle taillights and then tap into that…

view full answer...

Answer 3

The blue wire on the Trailer Wiring Adapter 4-pole to 5-pole is normally used for boat trailer connections where the trailer surge brakes need to be locked out. The blue wire is connected to the vehicles backup light circuit so that when the vehicle…

view full answer...

Answer 4

The Firestone Air Compressor 24-3582-9210 is no longer available but we do have a suitable replacement for this, the Firestone Heavy Duty Air Compressor part #F9499. This is what Firestone recommends you use to replace the Firestone Air Compressor…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

How Long is the Wire that Comes with Adapter for Back-up Light Connection?

Continue Researching