Can Bulldog Square Swivel Jack # BD190708 Be Fitted with a Caster Wheel Assembly

Question

Question:

Can you remove the leg and use a caster or wheel attachment?

asked by: Scott

1

Helpful Expert Reply:

The square-tube jack you referenced, the Bulldog Swivel Jack # BD190708, is a drop-leg type and this cannot be fitted with a caster assembly.

However we do offer a range of jacks that have caster wheels, both A-frame and side-mount types, and these can be viewed by clicking on the link to your right.

Do please note that any jack with a caster wheel will have a lower lift rating than the Bulldog. Wheels do not have the same weight capacity as a standard foot plate, so if a jack were available with either a fixed foot or a caster wheel, that same jack would have a lower capacity with the wheel installed than with the foot. The highest-rated caster-type jacks we offer carry a 1650-lb rating, such as the fXtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 10" Lift # ORJW750BD.

expert reply by: Adam R

1

Answer 1

The Extreme Off-Road Swing-Up Trailer Jack #ORJW750BD is listed as fitting 2" wide trailer tongues, but I reached out to Ark and you can still use it with your trailer. The jack uses M8 high tensile bolts so you will just need to find some that…

view full answer...

Answer 2

Thank you so much for the pictures and descriptions! It looks like you have the Pro Series Snap-Ring Swivel Marine Jack #PSEJ10000101 so for a replacement that will install directly to the mounting plate that is already welded on your trailer frame I…

view full answer...

Answer 3

When folded up and traveling the Xtreme Off-Road Ratcheting Trailer Jack item #ORJW750BD is 29" long from the top of the jack to the bottom of the wheels. From the bottom of the wheel to the center pivot point where the bracket attaches is…

view full answer...

Answer 4

I reached out to my contact at Ark and he was able to confirm that the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels #ORJW750BD you were looking at will work just fine on your seeder with a 2" x 2" frame. This jack offers up to…

view full answer...

Answer 5

Here is an image I have from the Xtreme Off-Road Swing-Up Trailer Jack #ORJW750D in zinc which will have the same dimensions as the black Jack #ORJW750BD you are looking at.

view full answer...

Answer 6

Since we don't have a jack quite tall enough for you really tall trailer the best option we have would be the #ORJW750BD with the wheel chock for jacks part #FT11933MI to help take up the extra room.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Can Bulldog Square Swivel Jack # BD190708 Be Fitted with a Caster Wheel Assembly

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching