Does the Replacement Truxedo Shur-Bond Velcro Brand Fastener # TX1115173 Use Glue to Install

Question

Question:

What type of glue do you recommend to apply the Velcro?

asked by: Kory

0

Expert Reply:

Actually when installed on the correct application the Replacement Truxedo Shur-Bond Velcro Brand Fastener # TX1115173 does not use any glues or 2-sided tape as it slides into the rail for a tonneau cover on a truck bed.

If you were looking to use this in an alternative application and wanted to secure it somewhere I would recommend something like Liquid Nails.

expert reply by: Jameson C

0

Answer 1

I have a solution for you, and the strips that you're referring to are going to come in a couple different sizes, but none of them are going to be 1-1/16" wide. The #TX1117876 strips you're referring to are 1" wide, which have the…

view full answer...

Answer 2

The hook piece on a Velcro setup is usually the piece that fails first, especially in a setup like this where the hook piece is attached to the vehicle and would be out in the sun. As long as your truck bed is 6-1/2 feet long and the cover you have…

view full answer...

Answer 3

The correct replacement velcro for you Truxedo tonneau cove is the Replacement TruXedo Shur-Bond Hook-And-Loop Fastener Strips #TX1117876. You will need to cut it to the size you need and it comes with the screws you need to install it.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

Hey Ross, the B and W Turnoverball #BWGNRK1067 wasn't designed to fit under a flat bed so there isn't an alternate set of measurements I can recommend. Are you sure it would clear under the flat bed? Normally we have to recommend the…

view full answer...

Answer 10

Hi Clint! I do have a couple center caps that I think will look nice on this tire/wheel combo, but the Goodyear Endurance ST205/75R14 Radial Tire w/ 14" Eagle Aluminum Wheel - 5 on 4-1/2 - LR D #GY57QB does not have any included with it. So with…

view full answer...

Answer 11

The Curt T-connector vehicle wiring harness for factory tow package 7 way and 4 pole flat connectors #C55774 is a confirmed replacement and fit for your Ford F-150 Lariat. It connects quickly and easily with no cutting or splicing of wires. The…

view full answer...

Answer 12

Yes. If you don't need the weight distribution bars attached to carry the trailer to storage, you can absolutely use just the WD hitch head and ball to tow the trailer. It will work just like a ball mount.

view full answer...

Does the Replacement Truxedo Shur-Bond Velcro Brand Fastener # TX1115173 Use Glue to Install

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching