Replacement Trailer Jack to Replace 2,000 Pound Fulton Jack

Question

Question:

I need to replace a Fulton #2228 trailer jack. What is the best one to use to replace it? Thanks.

asked by: Jim

0

Expert Reply:

The Fulton jack we carry that's closest to your current one is The Fulton F2 # F1413230134. It has a static capacity of 2,000 pounds and 10 inches of lift height. It's a bolt-on jack that fits 4 and 5 inch trailer frames. I've linked a review video fo you to take a look at.

expert reply by: Charles S

0

Answer 1

Hey Tim. There are only two jacks that will fit your current mounting bracket and they are both Fulton F2 jacks rated at 1,600 lbs. I have listed them below: Fulton F2 Swing-Up Trailer Jack, Dual 7" Wheels, Sidewind item #F1413060334 Fulton F2…

view full answer...

Answer 2

I spoke with my contact at Fulton, and the retracted height of the #F1413230134 jack from bottom of foot to center of mounting plate would be 5-3/8 inches when the bracket is at the lowest setting. When the bracket is slid to the highest setting, the…

view full answer...

Answer 3

The Fulton F2 trailer jack #F1413230134 can get pretty low. I went out to the warehouse and pulled one of these jacks to measure it. The mounting bracket is adjustable so with it in the lowest position from the bottom of the foot to the bottom of the…

view full answer...

Answer 4

I went out to our warehouse to take a look at the Fulton F2 Swing-Up Jack #F1413230134 referenced in your question. With the jack fully retracted, I measured a distance of right at 25 inches from the bottom of the footplate to the top of the jack.…

view full answer...

Answer 5

The Xtreme Off-Road Swing-Up Jack w/ Dual Wheels #ORJW500D and #ORJW350D are pretty similar with the only differences being the weight capacity, 1,100 lbs vs 770 lbs, and the total travel, 18-3/8" vs 12". Aside from that the mounting…

view full answer...

Answer 6

The Extreme Off-Road Swing-Up Jack w/ Dual Wheels - Sidewind - 1,100 lbs - Zinc #ORJW500D does not have a weld on option. It likely can be retrofitted to work with a bolt thru weld on bracket like the Jack Mounting Bracket for Fulton Marine Jack -…

view full answer...

Answer 7

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 8

With the ARK Xtreme Off-Road Swing-Up Jack #ORJW500D in its lowest position it is 6.49" from the center of the mounting point to the top of the jack. The other end of the jack when fully retracted is going to be 18.89" from the mounting…

view full answer...

Answer 9

Hey Steve, the schematic that shows the 645 mm measurement is for the #ORJW500D which is the Ark 500 Series Off-Road Jack. The answer that shows the 18" retracted length is referencing the #ORJW350D which is the 350 series jack and is smaller…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Trailer Jack to Replace 2,000 Pound Fulton Jack

Featured Help Information

Miscellaneous Media

Continue Researching