Replacement 7-Way Connector for 2007 Chevrolet Silverado

Question

Question:

does the plug slide into socket into a 2007 chevy silerado or twist I need it to slide in

asked by: John

0

Expert Reply:

The Hopkins Endurance Multi-Tow Trailer Connector, # HM40920, is a twist-in socket.

If you need a slide in replacement 7-way/4-way connector for your 2007 Chevrolet Silverado, you can use the Hopkins Custom Fit Vehicle Wiring, # 30955.

I have attached a video for you to check out.

expert reply by: Leah S

0

Answer 1

I can help you find the wiring harness you need for the brake controller; it will be underneath your dash to the left of the steering column. If you take a look the video I've linked, it will show you where the wiring harness is and how it will…

view full answer...

Answer 2

Yes, we have diagrams for nearly every type of trailer wiring connector available. Check out the link I attached to see them all. Most likely you have a 7-way on your 2008 Chevy Silverado so I attached a picture of a diagram of a 7-way.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Replacement 7-Way Connector for 2007 Chevrolet Silverado

Featured Help Information

Miscellaneous Media

Continue Researching