How to Remove an RV Exterior Light Lens Without Breaking It
Updated 09/23/2026 | Published 09/22/2026 >
Question:
Vengeance 2014 320A toy hauler, need to get cover off an oblong outside light. it is on the front kitchen side near bedroom, has water inside and looks awful. how do I remove cover without damage to the lens.
asked by: Edward R
Expert Reply:
Hey Edward, thanks for reaching out. Without knowing the exact light model, I can't say exactly where the release points are, but most of those older oblong RV porch/utility lights use a snap-on lens rather than screws through the face. Look along the bottom edge of the lens for a small notch or slot. Use a small flat-blade screwdriver or plastic trim tool in that notch and gently pry the bottom edge outward, then lift the lens off the tabs along the top. I would not pry against the middle of the lens since older plastic gets brittle and cracks pretty easily.
Since you already have water inside, once the lens is off, I recommend drying everything out and checking the housing for cracks. Also inspect the sealant around the light base where it meets the RV wall since that is often where the water gets in.
What is the brand and/or model number of the light?
Product Page this Question was Asked From
Trailer Clearance or Side Marker Light w/ Reflex Reflector - Rectangle - Amber Lens - Black Base
- Trailer Lights
- Clearance Lights
- Marker
- Rectangle
- Surface Mount
- Non-Submersible Lights
- Incandescent Light
- 4L x 2W Inch
- Amber
- Optronics
more information >
Continue Researching
- Search Results: locking hitch pin
- Search Results: accessory anti~rattle hitch anti~rattle
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2024 Honda CR-V
- Search Results: tekonsha 118467
- Search Results: foot plate
- Search Results: stabilizer kit
- Search Results: adapters
- Search Results: hitch anti~rattle
- Shop: etrailer Anti-Rattle Hitch Collar for 2.5" Hitch Receivers
- Video: Feature Review - etrailer Anti-Rattle Hitch Collar
- Video: 2017 Ford F-250 Super Duty Fit Verified - etrailer Anti-Rattle Hitch Collar
- Video: etrailer Anti-Rattle Hitch Collar Fit Check - 2026 Ford F-250 Super Duty
- Video: Review of etrailer Anti-Rattle 2.5 Inch Hitch Collar - e55YV
- Shop: Trailer Hitch
- Shop: BTBRV Magnetic Hitch Receiver Reducer Set - 3" to 2-1/2" & 2-1/2" to 2"
- Shop: Trailer Wiring
- Video: Lippert Components Trailer Jack LC362486 Review
- Shop: Replacement Foot Assembly for Lippert Components Power Stabilizer Jacks - Qty 1
- Shop: Replacement Front Foot Pad for Lippert Components Ground Control 3.0 Leveling System
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2019 Subaru Crosstrek
- Shop: B&W Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: RVpaws V2 Premium Articulating RV Jack Pads for 2" Square Jack Legs - 9" - Qty 2
- Shop: RV Jack Pads
- Shop: Suspension Enhancement
- Q&A: Replacement Wiper Seal for 2007 Lance 992 Camper
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)

