Thin factory jack feet are usually the first weak link in your camper's landing gear. When they bend or sink, these 9" steel pads swap in for the original feet, adding a wider footprint and built-in articulation for uneven ground.
If you've ever watched a factory pad start to curl at the edges while leveling, you already know the weak point. Thin stamped feet flex under load, and once they bend, the load shifts back into the jack leg itself. That's how minor deformation turns into long-term wear, alignment issues, and expensive hydraulic repairs.
These 9" pads fit standard 2" square leveling jack legs, including Lippert Ground Control 3.0, Lippert Venture, Atwood, and Stromberg Carlson landing gear systems, and include the pin connector for installation. Laser-cut from 1/4" plate steel and reinforced with six gussets, they're built to hold their shape when the weight comes down instead of flexing and fatiguing over time.
Campsites aren't all poured concrete. You back into what looks level, drop the jacks, and one corner always seems to settle differently. A rigid foot can force the jack to load at an angle, which adds strain where you don't want it. The integrated ankle pivots up to 10°, allowing the pad to adjust to slopes and uneven terrain. The leg stays aligned while the foot sits flatter on the ground, which helps the entire leveling system work the way it was intended. Instead of wondering if a soft site will leave you re-leveling in the morning, the jack stays aligned, the load stays distributed, and your leveling system holds its position overnight.
Soft soil, gravel pads, and sandy lakeside sites all test small jack feet. A narrow pad concentrates weight in one spot, which can lead to sinking and shifting as the ground compresses. The 9" round footprint redistributes that weight across a wider surface area, reducing how much the pad presses into the surface below. The broader base gives the jack more support underneath, especially when the ground isn't as firm as it first looked.
It only takes one hidden curb, rock, or raised edge to put a jack system in a bind. When a rigid foot meets an immovable object, something's gotta give, and that 'something' is often your hydraulics or frame. These pads are designed to detach first, sacrificing the foot instead of forcing that shock into components that cost far more to repair.
If you already run SnapPads, these steel feet can be paired with compatible 9" round SnapPad Xtra pads for added surface grip and ground protection. That gives you the strength of reinforced steel with the cushioning and traction of a removable pad system. If you don't have SnapPads yet, compatible options are available here on our site (SP54FR, sold separately).
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi everybody. Andy here with etrailer. Let's take a quick look together at these RV Paws V2 replacement RV foot pads for your two-inch square leveling jack legs. Now, this is going to be an upgraded replacement set of foot pads for your fifth wheel landing gear. So this is going to actually be the part obviously that sits on the ground when you level your trailer. And this is designed for to fit the standard two-inch square jack leg.
So it's gonna swap right in without any weird modifications needed. So where this really stands out is how this is going to handle real world conditions. The foot has a built-in pivot point, about 10 degrees or so. So instead of sitting awkwardly on uneven ground, it's going to adjust and stay flat and that's gonna give you better stability, especially on campsites that aren't perfectly level. You're also going to get this larger nine inch footprint, which is going to help spread out the weight.
So for instance, if you're parked on softer ground like dirt or gravel, it's going to be much less likely to sink in. Just confirming that diameter there with you. And if you also notice here, this does include this pin connector for attaching the replacement pads. And on your screen, I just wanna show you a picture of this in action. This is gonna be very easy to pin in your current jack leg into this new foot pad.
And the construction is heavy duty as well. This is made from quarter inch thick steel, and it's also reinforced with these gussets as you can see. So all that to say this is built to resist bending under those heavy loads. Another smart feature is the foot pads can actually detach if you hit something. That's going to help protect your landing gear and your trailer frame from damage instead of transferring all that force into the system.
Now if you want even more grip or protection, this is going to be compatible with Snappad Xtra pads that's snap onto the bottom. They're, of course, those rubber pads. I think in my opinion, this is going to be a great addition to these foot pads. So on your screen I put our part number for those Snappad pads. Take that part number, pop it in the search field of our website, and that will take you to the pads, and you can add that to your order if you so desire. But like I said, I think that would be a great addition to these. I think that's gonna wrap up our look today. One final note I wanted to make. This should be a pretty easy install, but if you think you need any help with installation whatsoever, we do have you covered on our product page. Underneath the photo section of this product page, we have a link that will take you to our installer locator. Click that link, answer the questions that it has for you, and that locator will find an installer in your area that etrailer has partnered with to do the work for you. Well, again, my name's Andy. Thank you for joining me.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.