Looking for Coupler Hinge Kit that Can Work on 2 inch by 3 inch Trailer Tongue

Question

Question:

My trailer tongue is 2” wide and 3” tall. Do you make a Swing King Bolt on Swing Tongue Kit for that size or will this one work with that tongue?

asked by: Brian T

0

Expert Reply:

Hey Brian, while we don't have a hinge kit that was designed for a trailer tongue that is 2 inch by 3 inch you could still use the # TD28FR but you would need to put 1/2 inch metal spacers on either side of the tongue to take up the extra space. What kind of trailer do you have?

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 3

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 7

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 8

Hey Donna, yes the Replacement Grease Cap for Dexter/Tie Down Engineering Vortex Trailer Hubs #DE69NR that you referenced does work as a replacement for your Dexter 21-261 cap. How do you like the Vortex trailer hubs?

view full answer...

Answer 9

Hello James, thanks for reaching out. Both the kits you mentioned, the Hydrastar #HYD22FR and #HYD42FR are complete conversion kits for standard 3,500 lb axles. The difference is the calipers included with each kit. The #HYD22FR has stainless steel…

view full answer...

Answer 10

The channel of the Demco 21K #DM16080-52 coupler is 3 inches deep. The distance from the center of where the trailer ball would sit to the first 5/8 inch hole is 7 inches, and 12 inches to the second hole. The Titan #T4853100 dimensions are a little…

view full answer...

Answer 11

Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…

view full answer...

Looking for Coupler Hinge Kit that Can Work on 2 inch by 3 inch Trailer Tongue

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching