Looking for 5 Lug Trailer Hub that Fits Spindle that is 1-1/16 inch Diameter

Question

Question:

Wondering if you have any boat trailer hub assembly that are 5 bolt 1 1/16 bearing size and 3 1/2 length of the hub

asked by: Janet A

0

Expert Reply:

Hey Janet, we do have the CE Smith Idler Hub part # CE13315 which has the bearing numbers and bolt pattern match. Usually you don't have to match the hub length like you asked about though so I am a little curious if that was a dimension you took because you thought we would need it or if it is something you know for sure you need from a hub replacement?

expert reply by: Jameson C

0

Janet

8/31/2026

It has to be a short hub. We bought a hub assembly and it was to long for the axel

Jameson C.

8/31/2026

@Janet makes sense. Yeah we don't have any that are shorter like what you need most likely but is your trailer older by chance?

Answer 1

You will want either the CE Smith Galvanized #CE13315 or Black #CE13311 idler hub assemblies. These both have the 1-1/16" ID bearings #L44649 and include grease seals for your 1-1/4" spindle diameter.

view full answer...

Answer 2

Hey Clyde, thanks for reaching out! From everything you described you're needing the CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles #CE13315. This comes pre-greased and in a protective case for shipping. The 5 on 4-1/2" bolt…

view full answer...

Answer 3

Hello Chris, Yes, we do have a hub that will work for you the CE Smith Trailer Idler Hub Assembly w/ Case for 2.7K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased #CE13315, or cast iron #CE13311. This hub has both inner and outer bearing L44649, and…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Looking for 5 Lug Trailer Hub that Fits Spindle that is 1-1/16 inch Diameter

Product Page this Question was Asked From

Continue Researching