What Bearing Kit Do I Need For A 2019 KZ-Durango 5th Wheel With Dexter 5,200 lb Axles?

Question

Question:

what bearing kit do I need for a 2019 KZ-Durango half ton 5th wheel with 5200lb dexter axels manufactured in 2018? Thanks

asked by: Brad S

0

Expert Reply:

Hey Brad, thanks for reaching out. Yes, we do have a bearing kit for the 5,200 lb axles on your 2019 KZ-Durango 5th wheel. Here is what you'll need:

- Bearing Kit, LM67048/25580 Bearings, 10-36 Seal # BK3-300

This comes with both bearings, races, grease seal and cotter pin. Everything you need to service your bearings.

Are you replacing all your bearings? Or just picking up a kit for a spare?

expert reply by: Jesse M

0

Bearing Kit, LM67048/25580 Bearings, 10-36 Seal
(click to enlarge)

Wes W.

8/15/2026

Bear Kit for 2018 Grand Design 29RS 5th Wheel. Replaced all four and install went seamlessly. Only couple of short trip since install but zero problems.

Ray

8/15/2026

I bought these bearings and seals for my trailer that has Dexter 5200 pound axles. Exact replacement!

Brad S.

8/17/2026

Thanks, I am just ordering a kit for a spare.

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 11

Hey Scott! The correct bearing kit for your Dexter 6k axle is the Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal #BK3-100. If you want the Dexter version it is the #DX26ER. What kind of trailer do you have?

view full answer...

Answer 12

Hi William! Thanks for the picture of your axle tag. The correct bearing kit is the #BK3-200 with a 10-36 grease seal. If you want the Dexter version it is the #DX58ER, Are you getting your Momentum ready for spring/summer? Any big trips coming up?

view full answer...

What Bearing Kit Do I Need For A 2019 KZ-Durango 5th Wheel With Dexter 5,200 lb Axles?

Product Page this Question was Asked From

Continue Researching