What Is the Best Replacement for a Dexter/Tie Down Model 660 Brake Actuator?
Updated 08/06/2026 | Published 07/29/2026 >
Question:
Dexter / Tie Down Model 660 Im looking to replace it as its in bad shape and not working. What would be the replacement model?
asked by: Clifford W
Expert Reply:
Hello Clifford,
Thanks for writing in!
The Dexter DX7.5 Drop-N-Go Brake Actuator for Disc Brakes, 2" Ball, Zinc Plated, 7,500 lbs # 099-175-20 is your best replacement for the Dexter/Tie Down Model 660. It uses the same mounting bolt pattern, so it is a straightforward swap without having to modify the trailer. I attached an image of one installed.
One of the biggest improvements with the newer Drop-N-Go actuator is how much easier it makes bleeding the brake system. Once everything is installed, fill the master cylinder with fresh DOT 3 or DOT 4 brake fluid and bleed the brakes by slowly stroking the actuator while opening and closing the bleeder screws at the calipers. I highly recommend having a second person help. It makes it much easier to watch for air bubbles and know when all of the air has been removed from the system. Be sure to keep a close eye on the fluid level in the reservoir throughout the process. If the reservoir runs dry, it will pull air back into the brake lines, and you'll have to start the bleeding process all over again.
One other tip is to skip the thread tape or thread sealant on the hydraulic brake fittings. These fittings seal at the flare, not the threads, so using tape is a common mistake that can actually cause leaks.
What body of water are you getting out on most, and what kind of boat do you have on that trailer? I have a little Ranger bass boat, we are in Missouri so I get out on the Lake of the Ozarks, but mainly Mark Twain Lake in the summer as the wakes get too bad at the Lake of the Ozarks in the summer. Still chasing that double digit bass, hoping to catch that in South Carolina next spring!
Product Page this Question was Asked From
Dexter DX7.5 Drop-N-Go Brake Actuator - Disc Brakes - 2" Ball - Zinc Plated - 7,500 lbs
- Brake Actuator
- Surge Brake Actuator
- Boat Trailer
- Construction Trailer
- Farm Trailer
- Travel Trailer
- Utility Trailer
- Bolt-On
- 7500 lbs GTW
- 2 Inch Ball Coupler
- 3 Inch Channel Tongue
- Disc Brakes
- Electric Lockout
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer brakes
- Shop: Dexter DX7.5 Drop-N-Go Brake Actuator - Disc Brakes - 2" Ball - Zinc Plated - 7,500 lbs
- Shop: Dexter DX7.5 Drop-N-Go Brake Actuator - Drum Brakes - 2" Ball - Zinc Plated - 7,500 lbs
- Shop: Dexter DX6.6 Drop-N-Go Brake Actuator - Disc Brakes - 2" Ball - Zinc Plated - 6,600 lbs
- Shop: Dexter DX6.6 Drop-N-Go Brake Actuator - Drum Brakes - 2" Ball - Zinc Plated - 6,600 lbs
- Video: Feature Review Dexter DX7.5 Drop-N-Go Brake Actuator
- Video: Review of Dexter Brake Actuator - Surge Brake Actuator - DX79UR
- Shop: Hydrastar Marine Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi
- Shop: Trailer Hitch
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: Installation Time for Blue Ox BX1128 Flat Tow Base Plate Kit for 2016 Jeep Grand Cherokee
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Q&A: Replacement for Atwood 61101 Brake Actuator
- Video: How To Choose Camper Leaf Springs
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer jack
- Shop: Base Plate for Tow Bar
- Article: Trailer Lighting Requirements




Neville B.
8/5/2026
I replaced my actuator with one. Everything bolted right up. I made an adapter out of the reservoir cap from the old one and used a power bleeder to bleed and refill.That washed all the old fluid and trash out. I pull a 25ft Carolina skiff and it stops fine. Would buy again.