Do I Have to Strip the Wires When Using the TowSmart 4-Way Flat Connector Repair Kit?

Question

Question:

I just purchased TowSmart 4-Way Flat Connector Rapid Repair Trailer Wiring Kit Part Number: TS68QR from you. When I install it, should I strip the wires or just put them in with insulation intact? Thank you!

asked by: Daniel C

0

Expert Reply:

Hey Daniel, welcome back! You do not have to strip the wires before installing them on the TowSmart 4-Way Flat Connector Rapid Repair Trailer Wiring Kit item # TS68QR.

The 4-way connectors have sharp metal prongs that slice the wiring insulation or sheath. Once you put the cap on it'll push the wires into the prongs. It'll give you a secure reliable connection for conducting the lighting signals from your tow vehicle.

I attached a couple of pictures below so you can see the prongs.

What kind of trailer are you replacing the 4-way connector on?

You can add this information, along with any other questions you have, where it says Add Comment.

expert reply by: Jerred H

0

TS68QR
(click to enlarge)

Answer 1

Since you do not have a need for trailer brake wiring I have just what you need. I recommend the T-One Wiring Harness, part #118341. This harness includes the converter you need for your 4Runner, so you do not need another converter. The converter…

view full answer...

Answer 2

Joey, great question because this is one of those details that can make or break how clean and secure your wiring connection ends up. For the TowSmart part #TS68QR, it’s designed for typical trailer light wiring, which generally falls in the 16 to 18…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Do I Have to Strip the Wires When Using the TowSmart 4-Way Flat Connector Repair Kit?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching