What Bearings and Seal Does CE Smith Trailer axle part # CES84XR Use

Question

Question:

Hello, I want to purchase this axle CES84XR but want to have an extra set of bearings and seals on hand, can you tell me what bearing and seal kit apply to this axle?

asked by: Blake L

0

Expert Reply:

Hey Blake, the bearings that the CE Smith axle part # CES84XR uses are # L44649 for both inner and outer bearings. Then for a hub seal you would want the part # 34823.

expert reply by: Jameson C

0

Answer 1

Thanks for the picture Rich. The BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter item #TRU44FR is exactly what you need if your hubs have item #L44649 inner and outer bearings. For a grease seal you'll want item #34823. We…

view full answer...

Answer 2

Hey Paul, are you asking about replacement zerk fittings that would fit the spindles of the axle? If so, this is not an EZ lube axle so it doesn't have those or have ability to have them added. Or were you asking about Bearing Buddies that…

view full answer...

Answer 3

Hey Gary, so the holes that are on the CE Smith trailer axle part #CES84XR are currently at 38-1/2 inch on center so there would easily be enough room to put new ones at just 3/4 of an inch past where they are now but you would need to rotate the…

view full answer...

Answer 4

Hey Tyler, thanks for reaching out. I'm sorry to say no, we don't have a 5 on 4-1/2" hub, or any hub for that matter that fits a 3/4" straight spindle. That kind of spindle was really only seen on older trailers and is basically…

view full answer...

Answer 5

I do have some options for you but none of our trailer axles match the exact measurements that you provided. Therefore, the best option we have for you would be to switch to an axle less system like the Timbren Axle-Less Trailer Suspension System…

view full answer...

Answer 6

Unfortunately, we do not have any trailer hubs with the bearings that you need. Would you be open to replacing the entire axle? This would be the only option we have for you. If so then I would need you to measure the distance between each hub face…

view full answer...

Answer 7

It sure would Eric! The CE Smith Trailer Axle Beam with Studded Hubs item #CES84XR is exactly what you need for a 49-1/2" hub face. This axle comes with two idler hubs that have a 5 on 4-1/2" lug nut pattern so it'll be perfect for you.…

view full answer...

Answer 8

Hey, Matt! We do have an axle that is 72" for the hub face but nothing that is 72.5". All of the axles that are 72" long have a spring center of 58". This is the approximate width of your trailer. It is measured from the center of…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

We sure do Brian. We've actually got two center caps that are going to work with the Kenda Karrier KR53 ST205/75R15 Radial Trailer Tire with 15" Black Aluminum Wheel item #KE58JV. Which one you go with is going to come down to personal…

view full answer...

What Bearings and Seal Does CE Smith Trailer axle part # CES84XR Use

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching