Recommended Trailer Hitch for a 2010 BMW 5 Series Sedan
Updated 07/22/2014 | Published 07/20/2014
Products Featured in This Question
Question:
Ive a 2010 BMW 535xi sedan. Id like to put a hitch on it and Ive read that you have a hitch that does not bolt on is removable. But I dont see it on your site. Is there a hitch were I can leave the lower pan on the car or modify it? OK having to bolt the hitch on. Thanks
asked by: Miles C
Helpful Expert Reply:
There is one trailer hitch that is a confirmed fit for your 2010 BMW 5 Series sedan. The Curt Class I trailer hitch, part # C11498 should work great for you. This is a bolt-on installation. Some underbody panels or fascia must be temporarily loosened or removed during installation.
We don't have any removable trailer hitches for your BMW 5 Series.
To see what it would take to install this hitch on your vehicle check out the picture I've attached that shows the installation instructions.
If you plan to do some towing, the hitch comes with a hitch pin and clip. For a ball mount you can use # C45521.
For a ball you can use # 19256 for a 1-7/8 inch diameter, or # 19258 for a 2 inch diameter. For trailer wiring, use # C59236. I have included a link to the installation details for the wiring as well.
This installation is on a different vehicle but can be used as a guide when installing the wiring on your vehicle.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- For Towing
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- No Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Video: Curt 4-Way Flat Trailer Connector Installation - 2022 Mercedes-Benz GLC
- Video: Curt Wiring - Trailer Connectors - C56496 Review
- Video: All About the Powered Converter Wiring Kit
- Search Results: wiring kit
- Search Results: trailer hitch
- Search Results: 55151
- Search Results: tow hitch
- Shop: Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Curt Towing Starter Kit for 1-1/4" Hitches - 2" Ball - 3/4" Rise - 3,500 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Powered Converter Wiring Kit
- Shop: Curt 4-Way Flat Trailer Connector with Circuit Protected Powered Tail Light Converter
- Shop: EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer wiring
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Video: Curt Powered Tail Light Converter Installation - 2023 Kia Telluride
- Shop: Brake Controller
- Search Results: trailer jack
- Video: Clean Up Your Trailer Wiring
on Trailer Hitch
