Does the B&W Tow & Stow Weight Rating Drop When Adjusting the Rise & Drop?
Updated 06/26/2026 | Published 06/23/2026 >
Products Featured in This Question
Question:
Is the hitch, part number BWTS10040B, rated for its full 10,000 lb rating with the 2 5/16” ball in the lowest position or does the weight rating go down the farther you ?
asked by: Blake
Expert Reply:
Great question Blake, thanks for asking!
Yes, the B&W Tow & Stow # BWTS10040B maintains its full 10k lb and 1k lb tongue weight rating when using the 2-5/16" ball, even when the ball is adjusted to the lowest drop position.
The height adjustment does not reduce the hitch's capacity. Just be sure your vehicle's hitch and towing setup are rated for the same weight and maintain at least 11" of ground clearance under the hitch to keep it from scraping the pavement.
What do you haul with the Tow & Stow?
Product Page this Question was Asked From
B&W Tow & Stow 2-Ball Mount - 2" Hitch - 7" Drop, 7-1/2" Rise - 10K - Black
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- Two Balls
- 2 Inch Ball
- 2-5/16 Inch Ball
- Steel Shank
- Drop - 7 Inch
- Rise - 7 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- B and W
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: bullet
- Search Results: bike rack
- Search Results: trailer breakaway kit
- Search Results: trailer breakaway switch
- Search Results: 100400c
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: 24x60 etrailer Cargo Carrier for 2" Hitches - Steel - Tilting - Folding - 500 lbs
- Shop: Weld-On Hinge with Stainless Steel Bushing and Pin - Aluminum - 7-7/8" Long - 5/8" Pin
- Shop: Dexter Double-Acting Hydraulic Trailer Jack Add-On - 20" Lift - 10,000 lbs - Direct Weld
- Shop: Weld-On Hinge with Brass Bushing - Steel - 10-1/4" Long - 3/4" Pin Diameter
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Brake Controller
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Suspension Enhancement
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Video: Curt Mounting Bracket for 4-Pole Flat Trailer Connector Review
- Article: How to Measure for Trailer Hitch Drop
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector


S
6/26/2026
Works well. I use the 2” ball for my 12’ single axle utility trailer. Before with a standard hitch the tongue of the trailer was tilted up. This caused it to bounce over bumps even with a load. The drop adjustment works great to keep the trailer level and allow the suspension to articulate correctly.