Parts Needed To Add Disc Brakes To A 2002 EZ Loader Trailer With No Brakes
Updated 06/25/2026 | Published 06/20/2026 >
Products Featured in This Question
Question:
My 2002 single axle EZ Loader boat trailer does not have brakes. The trailer VIN is: 1L8DADMD52A065943 I want to add marine rated disc brakes. Is your part no. T2HRCM10DAC the correct brake kit? Also, does this kit include the bolts necessary to mount the brakes to the square bracket on the trailer?
asked by: David K
Expert Reply:
Hey David, thanks for reaching out. The Dexter Premier Disc Brake Kit # T2HRCM10DAC will work for you, provided your EZ Loader trailer is equipped with a standard 3,500 lb axle. There isn't a way to look up that information using the VIN, so you'll definitely want to get under the trailer and check the axle tag/sticker and confirm this.
If you can't make out the axle sticker, you'll need to pull a hub and make sure the bearings are the standard # L68149 (1.378" inner diameter) inner bearing and # L44649 (1.063" inner diameter) outer bearing. As long as it is a standard 3,500 lb axle, you'll be good to go with the # T2HRCM10DAC kit which is marine grade.
The mounting bolts are not included with the disc brake kit, but we do sell those separately as part # BRKH10A.
From there, you'll just need a brake line kit like part # 18SI-BLKIT which comes with an 18' main line. You'll just want to measure from the coupler to the axle to make sure that main line is long enough.
Then pick up a surge brake actuator for disc brakes # DM62VR and you'll be all set. This has an electric lockout so you can wire it to the cars reverse light circuit. This will stop the brakes from locking up when you back the trailer up.
We have an article that goes over how to add disc brakes to a trailer, and I've linked that for you below.
How long is this trailer? It's a single axle, right?

Jaygyver
6/25/2026
The biggest concerns are the bearing size/number on the trailer now and the bolt circle on the bracket for the calipers. You might try going on EZLoaders website and see if you can narrow down what axle you have? If you haven't already read up on all their info for the bolt circle on the square brake caliper bracket on the trailer, etc. It helped me quite a bit when I had to gut my 40 yr old Calkins dual axle trailer and start all over with brake calipers, actuator, etc. As far as the brake cutout, I used and old crescent wrench on the external rails on my trailer for years, too lazy to hook up the electric actuator. Does kind of suck when the vehicle is pointed down hill when you try to slide it in tho......So I would still carry something to bypass it. I used the trailer in the Puget Sound a few times but mostly lake usage and the OEM disc brakes worked great. Calkins went belly up so replacement parts were non existent hence having to gut everything and start over. Account for securing the brake lines so they don't rattle or rub and I would use epoxy or something similar to hold any line brackets instead of drilling into the trailer frame. I did have a couple of hiccups ordering a couple of things but everything was fixed in the end so expect delays and you won't have any surprises.

Product Page this Question was Asked From
Dexter Premier Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Trailer Brakes
- Disc Brakes
- Marine Grade
- 5 on 4-1/2 Inch
- Hub and Rotor
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: brake line kits
- Shop: Dexter Premier Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Search Results: trailer brake master cylinder
- Search Results: dexter brake line kits
- Search Results: standard bearings trailer bearings races seals caps
- Search Results: bk2 100 bearing kit
- Search Results: bearing
- Search Results: boat trailer jack
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: Hands-On with the Dexter Premier Disc Brake Kit
- Shop: Demco DA75 Trailer Brake Actuator for Disc Brakes - Zinc Plated - 2" Ball - 7,500 lbs
- Shop: Lippert Complete Bearing Kit for 3.5K Trailer Axles - L44649/L68149 Bearings, L44610/L68111 Races
- Shop: Lippert 60-Degree Cone Trailer Wheel Lug Nut - 1/2"-20 - Qty 6
- Shop: Kodiak Hydraulic Brake Line Kit - Single Axle - 18'
- Shop: Demco Hydraulic Brake Line Kit - Drum Brakes - Single Axle - 20' Main Line
- Q&A: Is There a Demco Brake Line Extension or a Longer Brake Line Kit Than the DM5426 Kit
- Video: Review of the Demco Hydraulic Brake Line Kit for Single Torsion Axle Trailers
- Video: What to Know About the Demco Hydraulic Brake Line Kit
- Video: Hands-On with the Demco Hydraulic Brake Line Kit for Single Torsion Axle Trailers
- Video: Checking Out the Kodiak Hydraulic Brake Line Kit
- Video: Replacement Trailer Hub Bearing Spec Review
- Video: Checking Out the Demco Hydraulic Brake Actuator w/ Electric Lockout
- Q&A: Torque Spec to Use When Installing Mounting Bolts and Hardware # BRKH10A
- Q&A: New Brake Assemblies, Hub/Drums, Brake Lines, and Bearing Buddy for Trailer with 3,500 lb Axle
- Q&A: Replacement Brake Setup for Trailer with DB-42 Disc Brakes
- Q&A: Looking To Replace Tie Down Engineering Brake Pads And Rotors
- Article: Trailer Wiring Diagrams
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Q&A: Availability of Replacement Parts for Atwood 85736 Brake Actuator
- Q&A: Brake Upgrade Reccomendation For My UFP DB-42 Oil Bath Brakes




David K.
6/25/2026
Thanks, Jesse! My trailer is for a 19 ft boat and is single axle. And I'm pretty sure that the axle is 3500 lbs but I will confirm. My other boat and trailer has disc brakes and an actuator that uses a pin inserted to lock out the brakes if backing up. You mentioned that the DM62VR actuator has an electric lockout which sounds good. Does it also have a way of manually locking out the brakes (like a inserted pin) should the electric feature fail for some reason? You included a replacement trailer hub among the listed products. But would I need that if my existing bearings are the standard ones? Thanks again for your assistance! David