How Much Grease Should Be Added To Road Armor Wet Bolts On 2025 Keystone Montana High Country

Question

Question:

How much grease should be added to the wet bolts on the Road Armor Blue Equalizers on a 2025 Keystone Montana High Country when lubricating every six months?

asked by: John D

0

Expert Reply:

Hey John! The wet bolts on your Lippert Road Armor # LC53CK really only need a couple pumps of grease every 6 months. Lippert recommends applying grease until you see fresh grease begin to squeeze out around the bolt and bushing area. Once you see that, you're all set and can stop pumping grease.

It looks like you already picked up the LubriMatic LMX # L11390. This will work really well on the wet bolts and keep the suspension on your 5th wheel lubricated and protected from premature wear.

Any big trips coming up with the Montana?

expert reply by: Robin H

0

Lippert Road Armor
(click to enlarge)

John D.

5/26/2026

Thanks for the response Robin! We just completed a 3 week, 3000 mile trip from Texas to Gettysburg, PA, Nashville, TN, Hot Springs, AR and then home. Heading to Natchez, MS in June after we install the new Curt Flex Air pin box we just ordered from eTrailer.

Robin H.

5/26/2026

@JohnD you’re welcome! Sounds like an awesome trip. Gettysburg is actually next on my list too, I’ll be there in a couple weeks. The Curt Flex Air # LC369535 will make a noticeable improvement in ride quality for your trip to Natchez, especially on rougher highways. If you need anything else, don't hesitate to reach out.

Answer 1

I recommend using the LubriMatic LMX Industrial Strength Grease #L11390 on the Wet Bolts #LC52SV for the Road Armor Shock Absorbing Equalizer Kit #LC696740. This grease is formulated for superior performance in cold and hot climates. It is also…

view full answer...

Answer 2

By 'drawing', I'm assuming you're needing the bolt hole spacing, is that correct? Lippert won't provide a build sheet, because that's considered proprietary information, but I've provided a diagram showing the bolt hole…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Neil. The 18,000 Btu Furrion Chill Cube RV Air Conditioner item #LC34DX fits a 14-1/4" x 14-1/4" cutout which is pretty standard on RV's. If you meant to write Dometic instead of domestic then yes it'll fit in your existing…

view full answer...

Answer 11

Hi Bill! Thanks for your pictures, they were extremely helpful! ^___^ The LCI Part #194170 on that tag you found means you have a 1621 pin box. The Gen-Y #GY45SR you were looking at is specifically for the Lippert 1116 and 1716 pin boxes, so you will…

view full answer...

Answer 12

Hey John, this is a great question. I asked B and W about whether or not the B and W Fifth Wheel to Gooseneck adapter part #BW73RV would void the frame warranty and they said it has been extensively tested and engineered to provide a smooth, stable…

view full answer...

How Much Grease Should Be Added To Road Armor Wet Bolts On 2025 Keystone Montana High Country

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching