Replacement Breakaway Kit For A Brake Buddy Vantage Select Supplemental Braking System

Question

Question:

I have a brake buddy vantagenot vantage . Im in need of the breakaway plug for this unit. Can you help with that?

asked by: Mark B

0

Expert Reply:

Hey Mark,

For a Brake Buddy Vantage supplemental braking system you would need the Replacement Breakaway Kit for Brake Buddy Vantage Select Flat Tow Brake System # HM39327.

expert reply by: Kevin C

0

Answer 1

The Second Vehicle Breakaway Kit for Blue Ox Patriot Supplemental Braking Systems #BRK2505 is designed to work with the Blue Ox Patriot BRK2012 (NLA), Patriot II BRK2010 (NLA), BRK2016 (NLA), or the Patriot 3 BRK2019 (NLA). Unfortunately, this will…

view full answer...

Answer 2

Hey Monty, I did some checking and the breakaway switch part #RVI97FR that you referenced is the correct breakaway replacement for your Brake Buddy Classic. What are you flat towing?

view full answer...

Answer 3

On a 6-Pole, Round Pin, Plastic Trailer Wiring Socket #PK12720 there is typically only enough room for one wire for each terminal to mount inside the stud. You can still splice both the ground wires together and run a single wire into the terminal on…

view full answer...

Answer 4

I went out to the warehouse and pulled Pollak 6-pole vehicle side connector #PK11608 to measure the mounting hole spacing for you. The holes are 2-3/4 inches apart on center. The vehicle and trailer side connectors are different. The trailer side…

view full answer...

Answer 5

Yes, the Replacement Brake Buddy Vantage Select Break-Away System #HM39327 will fit your Brake Buddy Vantage Model 39504.

view full answer...

Answer 6

Yes, a breakaway switch only completes a circuit when the plunger is pulled. You can wire either of your trailer wires to either of the wires of the #HM20014 and it would work great. I attached an FAQ article on breakaway systems for you to check out…

view full answer...

Answer 7

I recommend using the Hopkins Breakaway Switch #HM20014 for your BrakeBuddy Vantage 39504. Breakaway switches are pretty universal so this will work well for your application. Please note that your Vantage uses banana clips to connect the switch to…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Replacement Breakaway Kit For A Brake Buddy Vantage Select Supplemental Braking System

Continue Researching