Looking for 3,500 lb Trailer Axle Hub with 5 on 5-1/2 inch Bolt Pattern and EZ Lube Style Grease Cap

Question

Question:

Does the TruRyde TRU26AV drum assembly come with EZ Lube style hub caps? Thanks!

asked by: Duane D

0

Expert Reply:

Hey Duane, the Trailer Hub and Drum Assembly # TRU26AV that you referenced does not come with EZ lube style grease caps but we do have the part # AKHD-555-35-EZ-K that does and is a 3,500 lb hub with a 5 on 5-1/2 inch bolt pattern. What trailer do you have?

expert reply by: Jameson C

0

Answer 1

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 2

Hey Jon, yes you sure can! And it's not too difficult either. If your vehicle already has a 4 way flat on the back, you can just install the #ETBC7 which converts it to a 7 way to be used with trailers that have electric brakes. Basically the 4…

view full answer...

Answer 3

The right and left orientation is determined if you are standing behind the trailer looking towards the tow vehicle. The left side is the drivers side and the right side is the passengers side. Tthe shorter brake pad will always be in the front of…

view full answer...

Answer 4

If you only have the nut and a washer but no cotter pin or retaining type washer on the end then that isn't correct and you want to get a piece to help prevent that nut from backing off. If you have a setup like the Spindle Nut Kit for EZ Lube…

view full answer...

Answer 5

Yes you can reuse the spindle nut as long as its threads are not ruined and it has good form/fit/function. If you do need a new one or want a spare for future use you can get some here. Replacement Spindle Nut for Dexter Nev-R-Lube Hub and Drum…

view full answer...

Answer 6

The etrailer.com hub and drum assembly, part #AKHD-545-35-K, includes one hub, one of each bearing, parts #L68149 and #L44649, one of each race, parts #L68111 and #L44610, the grease seal, part #58846, and one set of lug nuts. So you need two of the…

view full answer...

Answer 7

Hello Mike. It sounds like you are wanting to add electric brakes to your boat trailer that currently has no brakes. This is possible, but you will first need to make sure that your axle is equipped with a brake flange at the base of the spindle. The…

view full answer...

Answer 8

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Looking for 3,500 lb Trailer Axle Hub with 5 on 5-1/2 inch Bolt Pattern and EZ Lube Style Grease Cap

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching