Which Stainless Steel Lug Nuts to Use with Aluminum AM03 Series Gunmetal Trailer Wheel

Question

Question:

What length stainless steel lug nuts do I need for these wheels?

asked by: Tony W

0

Expert Reply:

Hey Tony, standard length stainless lug nuts like the part # DE55KR would be what you'd want to use with the trailer wheel Aluminum AM03 Series Gunmetal Gray Machined Trailer Wheel part # AM73NR that you referenced.

expert reply by: Jameson C

0

Answer 1

Hey Mike, if you are wanting a higher quality one piece 1/2 inch lug nut for your 2021 Grand Design Reflection 295RL I would recommend the stainless steel one piece part #DE46NR over the #12CLN. Stainless won't corrode and swell whereas chrome is…

view full answer...

Answer 2

Hello Don, thanks for reaching out. The Americana Aluminum Trailer Wheel #AM43FV can use standard tapered-style or coned lug nut like part #12CLN. For a 13" aluminum wheel with 1/2" studs, the torque spec would be 75-85 ft.-lbs. I have…

view full answer...

Answer 3

Hey Shane, thanks for reaching out! The Karrier ST205/75R15 Radial Trailer Tire with 15" Aluminum Wheel #KE63JR that you're asking about doesn't come with lug nuts, but you will need to use 1/2"-20 lug nuts, like the Redline #12CLN,…

view full answer...

Answer 4

Hi Mark; the Aluminum AM03 Series Gunmetal Gray Machined Trailer Wheel #AM73NR uses acorn style lug nuts with a 60° cone like the #12CLN. An ST175/80D13 tire like the #AM1ST77 will fit a 13" x 4-1/2" rim.

view full answer...

Answer 5

It is not usually necessary to change wheel studs when switching from stamped steel trailer wheels to machined aluminum wheels like the Lionshead #LHSJ211G but I went to our warehouse to measure the thickness of the material at this wheel's hub,…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Which Stainless Steel Lug Nuts to Use with Aluminum AM03 Series Gunmetal Trailer Wheel

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching