Is Replacement Adapter Port for DeeMaxx Disc Brake Calipers # DE73MR Exact Replacement Part

Question

Question:

Is this part exactly the same as the one that came on the caliper?

asked by: Mason

0

Expert Reply:

Hey Mason, yes the Replacement Adapter Port for DeeMaxx Disc Brake Calipers # DE73MR that you referenced is an exact replacement for the port that was on your DeeMax caliper. Did you lose yours?

expert reply by: Jameson C

0

Answer 1

Hey Mason, yes your 3/16 inch brake line will connect to the Replacement Adapter Port for DeeMaxx Disc Brake Calipers #DE73MR as that is the size brake line it was designed to fit. Did you lose one off your DeeMaxx caliper?

view full answer...

Answer 2

The Adapter Port #DE73MR you found is an exact replacement for the one on the Caliper #DE86VR. This is designed to accept a brake line like the Kodiak #bh-3mfs90ff-1-5 and not a banjo type connection. You are going to have to alter your brake lines…

view full answer...

Answer 3

Hey Ray, sorry about that! The pictures and video are correct for the DeeMax Brake Line part #DE99NR. IT's basically a 90 degree male on one side and a straight male on the other side. I will send an update to have the title fixed thanks!

view full answer...

Answer 4

It should, Gene. The DeeMaxx Hydraulic Brake Line Kit #DE37SR is designed for triple axle trailers, and will work great with with disc and drum brakes. You're just going to need to make sure the fitting sizes are the right size. This kit uses…

view full answer...

Answer 5

hey Beth, yes the DeeMaxx brake line part #DE58GR that you referenced will work with the Dexter drum brakes that you mentioned as well.

view full answer...

Answer 6

Finding information on the Tie Down 46250 was not an easy task as it was discontinued awhile back. From what I could find, it looks like the calipers marked 46250 often times have to change the mounting bracket and rotor/hub in addition to the…

view full answer...

Answer 7

For the DeeMaxx Disc Brake Kit #DE22FR you will need to remove the Adapter Port #DE73MR and clean off the thread sealant. Then you will be able to apply new sealant when you position the port back on in the orientation you need.

view full answer...

Answer 8

Brake calipers are typically installed so they point toward the back of the trailer, but it is okay to install them pointing up or toward the front of the trailer. The important thing to consider when installing the calipers is to make sure at least…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Is Replacement Adapter Port for DeeMaxx Disc Brake Calipers # DE73MR Exact Replacement Part

Product Page this Question was Asked From

Continue Researching