What is Retracted Height of etrailer Dual-Pin Two-Speed Square Tube Jack # e45YV

Question

Question:

Redacted hight of this jack?

asked by: Daniel

0

Expert Reply:

Hey Daniel, when the etrailer Dual-Pin Two-Speed Square Tube Jack # e45YV that you referenced is fully retracted it's overall height is 29-1/2 inches.

expert reply by: Jameson C

0

Jameson C.

12/8/2025

Hey Daniel, did the 29-1/2 inch retracted height on that dual-pin two-speed jack end up working for your setup? Knowing how it fit could help others choosing the same jack.

Answer 1

This updated design etrailer Dual-Pin Two-Speed Square Tube Jack - 20,000 lb Static / 12,000 lb Lift #e45YV allows you to keep the crank handle on the upgraded 2 speed side and just switch between gearing ratios by pulling or pushing in. It still has…

view full answer...

Answer 2

Hi Jon, It sounds like you're looking for replacement jacks for a landing gear system for a trailer. The etrailer Dual-Pin Two-Speed Jack w/ 20,000lb Static capacity part #e45YV can be used in a landing gear system as it has the fitting a cross…

view full answer...

Answer 3

Hi Wade, Yes, you’ve definitely got some good options to get away from hand cranking, and I totally get wanting something easier, especially with a cattle trailer. A lot of cattle trailers are gooseneck style and use a square center-mounted jack like…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

What is Retracted Height of etrailer Dual-Pin Two-Speed Square Tube Jack # e45YV

Product Page this Question was Asked From

Continue Researching