Which MORryde X-Factor Works with CRE4000 Cushioned Equalizer

Question

Question:

I have a mr99zr will it work with cre 4000

asked by: Bryan

0

Expert Reply:

Hey Bryan, the MORryde X-Factor that is designed to work with the CRE4000 would actually be the part # MR33WR instead of the # MR99ZR. Are you set on getting the CRE4000?

expert reply by: Jameson C

0

Jameson C.

11/13/2025

Hey Bryan, did you end up going with the X-Factor that fits the CRE4000? Knowing what you chose could help others figure out which crossmember works best with their setup.

Answer 1

Hey Peyton, The XFactor crossmembers are determined by what eqalizers you have on your trailer. There are 2 options from MORyde that we carry. The MORyde #MR99ZR is for a MORyde LRE, RE, or TRE suspension system. While the other MORyde crossmember…

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

For replacement wet bolts you can use the #LC126238 which is 2-5/16" long or #LC126197 which is 3-3/8" long. I'm not sure which broke off so I would match them to the length of the broken bolts. The length is the usable length of the…

view full answer...

Answer 4

Hey Calvin, For a suspension upgrade kit on your Arctic Wolf 5th wheel trailer what you need to do is measure the length of your shackle straps from center to center to get the right length. Based on those lengths you will need either of the…

view full answer...

Answer 5

Hello Joe, I can definitely point you in the right direction. I do not have a way to look up your camper to know specs for the leaf springs, equalizers or shackles though, so I will need a bit more information from you in order to recommend the…

view full answer...

Answer 6

In order to find the correct suspension upgrade kit you are going to need to take some measurements. We do not have one that includes the equalizers based on your axle spacing so you will need to get those separately. Starting with your shackles, the…

view full answer...

Answer 7

The Road Armor Shock Absorbing Equalizer Kit - Tandem Axle - Qty 2 #LC696740 will work well with your current shackle strap length and won't have a big impact on ride height. Unless there is a drastic difference in the equalizer size it is best…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Which MORryde X-Factor Works with CRE4000 Cushioned Equalizer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching